Abstract:Single-phase Li0.5-0.5xZnxFe2.5-0.5xO4 (where x=0.0, 0.2, 0.3, 0.4, 0.5 and 0.8) nanofibers with diameters of 50 similar to 100 nm were successfully fabricated via electrospinning technique in combination with subsequent heat treatment using polyvinylpyrrolidone, nickel nitrate, zinc nitrate and ferric nitrate as principal raw material. The thermal decomposition process of as-spun precursor nanofibers and the influences of the calcination temperature and chemical composition on the crystal structure, micromorphology and magnetic properties of the prepared nanofiber samples were investigated by means of thermogravimetric and differential thermal analysis, X-ray diffraction, field emission scanning electron microscopy, transmission electron microscopy and vibrating sample magnetometer. The results indicate that the pure crystalline LiZn ferrite nanofibers are basically formed when the precursor nanofibers are calcined at 350 degrees C for 2 h. As the calcination temperature increases from 350 to 600 degrees C, the average grain size of Li0.35Zn0.3Fe2.35O4 nanofibers ranges from 13.0 to 47.5 nm and the micromorphology evolves toward a chain-like structrue. The saturation magnetization of the samples monotonously increases from 39.7 to 84.5 A.m(2).kg(-1), while the coercivity increases initially, reaches a maximun value of 12.6 kA.m(-1) at 550 C and then decreases, which reveals that the magnetic single-domain critical size of Li0.35Zn0.3Fe2.35O4 nanofibers may be around 35 nm. The lattice constant of as-prepared Li0.5-0.5xZnxFe2.5-0.5xO4 nanofibers calcined at 500 degrees C for 2 h exhibits an almost linear increase with increasing x and complies with Vegard's law. The coercivity of these nanofiber samples gradually decreases from 17.1 kA.m(-1) for x=0.0 to 2.4 kA.m(-1) for x=0.8, and the saturation magnetization firstly increases to 74.7 A.m(2).kg(-1) with the value of x up to 0.3 and then decreases beyond this limit. Compared to the nanoparticle counterparts prepared under similar conditions, the LiZn ferrite nanofibers have a relatively high coercivity due to their large shape anisotropy. These LiZn ferrite nanofibers have potential application in many fields such as nanoelectronic devices, sensitive devices, microwave absorbers, and biomedicine.

Preparation of Li6Zr2O7 Nanofibers with High Li‐Ion Conductivity by Electrospinning

Electrospinning Preparation, Structural and Magnetic Properties of Li0.5-0.5xznxfe2.5-0.5xo4 Nanofibers

Fabrication of dense and porous Li2ZrO3 nanofibers with electrospinning method

Highly Enhanced Electrical Conductivity in Electrospun La9.6Si6O26.4 Nanofibres

LaMnO3 and La0.875Sr0.125MnO3 Nanofibers via Electrospinning

LaMnO_3 and La_(0.875)Sr_(0.125)MnO_3 Nanofibers via Electrospinning

Nanostructured LiCoO2 and LiMn2O4 fibers fabricated by a high frequency electrospinning

Electrospinning Synthesis of Hollow V0.95mo0.97o5 Nanofibers for High-Performance Lithium-Ion Batteries

Nanofibers of LiMn2O4 by electrospinning

Fabrication of Li7La3Zr2O12 Fibers Using Bio-Mass Template Kapok

High Conductivity of La2Zr2O7nanofibers by Phase Control

Facile Synthesis of Interwoven Znmn2o4 Nanofibers by Electrospinning and Their Performance in Li-Ion Batteries

Preparation and Characterization of Sc2o3-Doped Zro2 Nanofiber

Electrospun Li3.9Cr0.3Ti4.8O12 Nanofibers As Anode Material for High-Rate and Low-Temperature Lithium-Ion Batteries

Preparation and Characterization of ZrO2 Nanofibers and Nanobelts by Electrospinning

Synthesis and Electrochemical Characterization of La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3– δ and BaZr 0.8 Y 0.2 O 3– δ Electrospun Nanofiber Cathodes for Solid Oxide Fuel Cells

Fabrication and electrochemical characteristics of electrospun LiMn2O4 nanofiber cathode for Li-ion batteries

Preparation and Characterization of Polycrystalline La2Zr2O7 Ultrafine Fibres Via Electrospinning.

Electrospinning Of Crystalline Moo3@C Nanofibers For High-Rate Lithium Storage

Enhanced Rate Performance of Lini0.5mn1.5o4 Fibers Synthesized by Electrospinning