Abstract:Rotationally symmetric workpieces of Ti2AlNb-based alloys have great potential for high-temperature service condition in aviation industry, while the poor workability limits their application until now. In this study, shear spinning and heat treatment were first conducted to investigate the corresponding microstructure evolution and mechanical properties of Ti2AlNb conical workpieces. The microstructure of the 1st and 2nd pass spun workpieces (SP1 and SP2) mainly consisted of B2 + retained alpha(2) phases. After two passes spinning, the B2 phase texture changed from <111>//ND of as-received alloy to be <001>//ND. The ultimate tensile stress (UTS) of SP1 and SP2 was increased to 1163 MPa and 932 MPa, respectively, compared with 782 MPa of as-received alloy at 650 degrees C. Also, the yield stress anomaly (YSA) occurred in SP1 and SP2 because {110}<111> and {112}<111> cross slip systems of B2 phase were difficult to slip at or below room temperature (RT), but they became active at 650 degrees C and above. As an essential step for increasing the spinnability of multi-pass spinning process of the Ti2AlNb alloy, the H3 heat treatment scheme, i.e. 960 degrees C/2 h+ 850 degrees C/12 h, was carried out between two successive passes to increase the hot workability, by which the ductility of the heat treated as-spun workpieces with the microstructure of B2 + primary O + acicular secondary O + high amount spheroidized alpha(2) phases reached 72.1% at 900 degrees C. After being subject to the H1 heat treatment scheme, i.e. 960 degrees C-2 h, the spun workpieces with the microstructure of B2 + primary O + intergranular primary alpha(2) phases achieved an optimized comprehensive mechanical properties both at room temperature and 650 degrees C, which should be chosen as the post-spinning heat treatment process for the service requirement. (C) 2022 Published by Elsevier Ltd on behalf of The editorial office of Journal of Materials Science & Technology.

Power Spinning of the Curved Head with Tailor Welded Aluminum Alloy Blank: Deformation, Microstructure, and Property

A Systematic Study on the Effects of Process Parameters on Spinning of Thin-Walled Curved Surface Parts With 2195 Al-Li Alloy Tailor Welded Blanks Produced by FSW

Influence of Friction Stir Weld Seam Distribution on Spun Formed Workpieces

Study on the spinning process of thin-walled aluminum alloy vessel head

Microstructure evolution and strengthening mechanisms of electron beam welded 2219 aluminum alloy plate after hot spinning and heat treatment

Effect of Multi-Pass Power Spinning on Microstructure Homogenization and Mechanical-Property Strengthening of Ti2AlNb-Based Alloy Using Welded Tube Blank

Spinning Process of 2219 Aluminum Alloy Tubes for Used in Hydroforming

Study on Spinning Process of A Thin-Walled Aluminum Alloy Vessel Head with Small Ratio of Thickness to Diameter

Study on the Spinning Process of Cylinder-Conical Composite Curved Generatrix Workpiece of TA15 Titanium Alloy

Mechanism of Increasing Spinnability by Multi-Pass Spinning Forming – Analysis of Damage Evolution Using a Modified GTN Model

Analysis of ball spinning formability of thin-walled tubular parts of aluminum alloy

Numerical Simulation on Formability of Tailor-Welded Blank with Curved Weld-Line under Different Blank Holder Forces

Study on Flange-Constrained Spinning Process for Hemispherical Aluminum Alloy Part

Tube-spinning Microstructure and Preferential Orientation of BT20 Alloy

Forming Quality of Heat Spinning for the Ni-Cr-W-Mo Superalloy Workpiece with Strange Shape

Research on Design Method of Variable Thickness Blanks for Aluminum Alloy Head Spinning Forming

Enhancing Hoop Strength of Titanium Alloy Tube by Cross Spinning

Study on microstructure evolution of TA1 during plane compression and its similarity to power spinning

Process Design and Microstructure-Property Evolution During Shear Spinning of Ti2AlNb-based Alloy

Research of Net-Shape Power Spinning Technology for Poly-V Grooved Aluminum Pulley

Experiment of Laser Assisted Shear Spinning for Aluminum Alloy Spherical Thin-Walled Parts