Abstract:The need for 2219 aluminum alloy and 2195 Al–Li alloy dissimilar friction stir welding (FSW) arises as the conventional 2219Al alloy was gradually replaced by the novel 2195Al alloy in fabrication of fuel tanks. However, the systematic investigation about the effect of welding parameters and material positioning on the microstructure evolution and mechanical properties of dissimilar FSW 2219Al/2195Al joints is lacking. In the present study, 2219Al-T8/2195Al-T8 plates were subjected to FSW under rotation rates of 800–1200 rpm and welding speeds of 200–800 mm min −1 with placing 2219Al-T8 alloys on the advancing side (AS) and retreating side (RS), respectively. The results showed that sound FSW joints were obtained under all the welding conditions. Welding parameters and material positioning affected the joint strength and fracture failure behavior. The FSW thermal cycle resulted in low hardness zones (LHZs) on both the 2219Al-T8 and 2195Al-T8 sides. The LHZ on the 2219Al-T8 side, characterized by partial coarsening of θ ′ (Al 2 Cu) precipitates and dissolution of the residual precipitates, showed the minimum hardness in the entire FSW joints. When 2219Al-T8 alloy was placed on the AS, the LHZ on the 2219Al-T8 side experienced higher peak temperature, and therefore more dissolution of θ ′ than that on the RS, thereby obtaining higher tensile strength. The tensile strength of the FSW joints at room temperature and − 196 °C largely increased as the welding speed increased from 200 to 400 mm min −1 . The FSW joints presented much higher tensile strength at − 196 °C than that at room temperature under the identical welding parameters and material position. The FSW joints fractured along the LHZ on the 2219Al-T8 side during tension. For the bending testing, the up and down bending failure angles were about 91–117° and 88–109°, respectively, with the weak zone appearing in "S" line or HAZ on the 2195Al-T8 side.

Microstructural Characteristics and Mechanical Properties of Friction Stir Welded 2219 Aluminum Alloy Plate After Spinning and Heat Treatment

Microstructure evolution and strengthening mechanisms of electron beam welded 2219 aluminum alloy plate after hot spinning and heat treatment

Microstructure and properties of friction stir welding 6061 aluminum alloy joint

Microstructure, mechanical and fracture properties of friction stir welded 2195 Al-Li alloy joints

Friction Stir Welding Characteristics of Different Heat-Treated-state 2219 Aluminum Alloy Plates

Microstructure and Mechanical Properties in Friction Stir Welded 5A06 Aluminum Alloy Thick Plate

Spinning Process of 2219 Aluminum Alloy Tubes for Used in Hydroforming

Friction Stir Welding of 2219-T6 Aluminum Alloy

Dissimilar friction stir welding of 2219-T8 and 2195-T8 aluminum alloys: part I—microstructure evolution and mechanical properties

Microstructure Evolution and Mechanical Properties of Friction Stir Welded Al–Cu–Li Alloy

Microstructural Characteristics and Mechanical Properties of Friction Stir Spot Welded 2A12-T4 Aluminum Alloy

Friction Stir Welding Characteristics of 2219-T6 Aluminum Alloy Assisted by External Non-Rotational Shoulder

Microstructures and Mechanical Properties of Non-thinning and Penetrating Friction Stir Welded 2219-T6 Aluminum Alloy

Residual Stress, Microstructure and Mechanical Properties in Thick 6005A-T6 Aluminium Alloy Friction Stir Welds

Mechanical Properties and Microstructure Analysis of Refilling Friction Stir Welding on 2219 Aluminum Alloy

Microstructures and Mechanical Properties of Micro Friction Stir Welding (μfsw) of 6061-T4 Aluminum Alloy

Microstructure and mechanical properties of friction stir welded powder metallurgy AA2024 alloy

Microstructure, mechanical properties and corrosion of friction stir welded 6061 Aluminum Alloy

Effect of Friction Stir Welding Parameters on Microstructural Characteristics and Mechanical Properties of 2219-T6 Aluminum Alloy Joints

Investigation on Material Flow and Microstructural Evolution Mechanism in Non-Thinning and Penetrating Friction Stir Welded Al–Cu Aluminum Alloy