Abstract:In recent years, weight reduction of automobile bodies has been effective in reducing carbon dioxide emissions. For this reason, the replacement of steel, which has a large specific gravity, with aluminum alloys and carbon fiber reinforced plastics is being promoted for the right materials in the right places. In this case, an appropriate dissimilar material joining method is needed in terms of ease of assembly, joining performance, and cost. Friction stir welding (FSW) has emerged as a promising joining method for a variety of engineering applications. FSW is a solid-phase joining technique that has been shown to have significant advantages over conventional welding in terms of the strength and quality of the joints produced. However, during joining of metallic materials by FSW, microstructural changes may occur that affect their corrosion degradation. In this study, the corrosion behavior of A6061 jointed with high-strength steel (SPCC980) by FSW in aqueous NaCl solution and the effect of Al alloy microstructural changes on it were investigated. In this study, FSW was performed on A6061 and SPCC980 steel plates, and galvanic corrosion behavior was investigated by immersion tests and surface observations, as well as electrochemical measurements of Al alloys. Immersion tests were performed in 1 M NaCl solution. Micro electrochemical polarization tests of A6061 were also performed to investigate the corrosion behavior. In the immersion test of the galvanic couple of A6061 and SPCC980 steel plates in NaCl solution, galvanic corrosion occurred with the Al alloy as the anode and the steel plate as the cathode, and hydrogen evolution was observed mainly from the BM site on A6061 in the initial stage of immersion. This is due to the hydrogen evolution reaction occurring inside the pitting corrosion of the A6061. The pits was formed near Fe-rich inclusions in the BM site. In the HAZ site, corrosion propagated from Fe-rich inclusions along grain boundaries, but no pitting corrosion was formed. In the NZ site, minor localized corrosion was developed. These results indicate that the susceptibility to localized corrosion and its morphology differ in each site on the A6061. The difference in localized corrosion susceptibility on the A6061 was considered to be caused by the difference in the distribution of Fe-rich inclusions. However, the fact that the size and number of Fe-rich inclusions in each site did not differ suggests that the difference in anodic dissolution activity near Fe-rich inclusions affects pitting corrosion susceptibility in each site. A6061 alloy is a precipitation-strengthened Al alloy reinforced by β'' phase, which is a metastable phase of Mg 2 Si, and dense precipitation of β'' phase was observed in the BM site. Therefore, the reason for the higher localized corrosion susceptibility of BM is related to the precipitation of the β'' phase. This paper is based on results obtained from a project, JPNP14014, commissioned by the New Energy and Industrial Technology Development Organization (NEDO).

Microstructure, mechanical properties and corrosion of friction stir welded 6061 Aluminum Alloy

Electrochemical and mechanical behaviors of dissimilar friction stir welding between 5086 and 6061 aluminum alloy

Friction stir welding of a rapidly solidified thin-strip continuous cast AA5182 Al–Mg alloy: analysis of microstructure evolution, mechanical properties, and corrosion resistance

Residual Stress, Microstructure and Mechanical Properties in Thick 6005A-T6 Aluminium Alloy Friction Stir Welds

Microstructure, microhardness and mechanical behavior of dissimilar AA7075/AA6061 alloys under friction stir welding

Microstructure, MAO Performance, Interfacial Characteristics and Corrosion Behavior of FSW Joint of Al-Mg-Sc Alloy

A study on the mechanical property and corrosion sensitivity of an AA5086 friction stir welded joint

Microstructure-strength relationship in friction-stir welded 6061-T6 aluminum alloy

Microstructure Evolution and Mechanical Properties of Friction Stir Welded Al–Cu–Li Alloy

Corrosion Behavior of Al Alloy A6061 Jointed with High-Tensile Strength Steel By Friction Stir Welding in NaCl Solution

Corrosion Behavior of Friction Stir Welded AA8090-T87 Aluminum Alloy

Mechanical properties and corrosion resistance study of dissimilar metal thin sheet friction stir welded joints

Microstructure, mechanical and fracture properties of friction stir welded 2195 Al-Li alloy joints

Post-weld heat treatment effects on microstructure, crystal structure, and mechanical properties of donor stir–assisted friction stir welding material of AA6061-T6 alloy

Experimental Study on Mechanical Behaviour of Friction Stir Welded Aluminium Alloy Butt Joints

Welding Investigation on AA6063-T6 Aluminium alloy during Friction Stir Welding process

Analysis of the Microstructure and Properties of Friction Stir Weld Zones in the Al 2139‐T8 Alloy

Microstructure and mechanical properties of friction stir welded powder metallurgy AA2024 alloy

Parametric effect on microstructure evolution, grain size and mechanical behaviour of friction stir butt welding of AA6061-T6 alloy

Friction Stir Welding of AZ31B Magnesium Alloy with 6061-T6 Aluminum Alloy: Influence of Processing Parameters on Microstructure and Mechanical Properties

Influence of Material Properties on Microstructure and Mechanical Properties of Aluminum Alloy FSW Joints