Abstract:Rotationally symmetric workpieces of Ti2AlNb-based alloys have great potential for high-temperature service condition in aviation industry, while the poor workability limits their application until now. In this study, shear spinning and heat treatment were first conducted to investigate the corresponding microstructure evolution and mechanical properties of Ti2AlNb conical workpieces. The microstructure of the 1st and 2nd pass spun workpieces (SP1 and SP2) mainly consisted of B2 + retained alpha(2) phases. After two passes spinning, the B2 phase texture changed from <111>//ND of as-received alloy to be <001>//ND. The ultimate tensile stress (UTS) of SP1 and SP2 was increased to 1163 MPa and 932 MPa, respectively, compared with 782 MPa of as-received alloy at 650 degrees C. Also, the yield stress anomaly (YSA) occurred in SP1 and SP2 because {110}<111> and {112}<111> cross slip systems of B2 phase were difficult to slip at or below room temperature (RT), but they became active at 650 degrees C and above. As an essential step for increasing the spinnability of multi-pass spinning process of the Ti2AlNb alloy, the H3 heat treatment scheme, i.e. 960 degrees C/2 h+ 850 degrees C/12 h, was carried out between two successive passes to increase the hot workability, by which the ductility of the heat treated as-spun workpieces with the microstructure of B2 + primary O + acicular secondary O + high amount spheroidized alpha(2) phases reached 72.1% at 900 degrees C. After being subject to the H1 heat treatment scheme, i.e. 960 degrees C-2 h, the spun workpieces with the microstructure of B2 + primary O + intergranular primary alpha(2) phases achieved an optimized comprehensive mechanical properties both at room temperature and 650 degrees C, which should be chosen as the post-spinning heat treatment process for the service requirement. (C) 2022 Published by Elsevier Ltd on behalf of The editorial office of Journal of Materials Science & Technology.

Effect of power spinning and heat treatment on microstructure evolution and mechanical properties of duplex low-cost titanium alloy

The Effect of Heat Treatment on the Microstructure and Mechanical Properties of the Novel Low-Cost Ti-3Al-5Mo-4Cr-2Zr-1Fe Alloy

Microstructure Regulation and Strength-Elongation Synergy of the Near Alpha TZAM Alloy Via Thermomechanical Processing

Effect of Ti on Microstructure and Mechanical Properties of Die-Cast Al-Mg-Zn-Si Alloy

Effect of Multi-Pass Power Spinning on Microstructure Homogenization and Mechanical-Property Strengthening of Ti2AlNb-Based Alloy Using Welded Tube Blank

Process Design and Microstructure-Property Evolution During Shear Spinning of Ti2AlNb-based Alloy

Strain-dependent Heterogeneity of Microstructure and Mechanical Properties of 2195 Al-Li Alloy During Power Spinning and Heat Treatment

Heat-treatment induced microstructural evolution and enhanced mechanical property of selective laser melted near β Ti-5Al-5Mo-5 V-3Cr-1Zr alloy

Effect of Hot Rolling and Heat Treatment on Microstructure and Tensile Properties of High Strength Beta Titanium Alloy Sheets

Tailoring the microstructure and mechanical property of laser powder bed fusion fabricated Ti–6Al–2Sn–4Zr–2Mo via heat treatment

Influence of Α+β Solution Treatments on Ti65 Ultrathin Sheets: Silicide Precipitation, Mechanical Behaviour and Novel{101¯1}twinning System

Study on Strong Spinning Preparation Method and Mechanism of the Industrial Pure Titanium Ultrafine Crystallization

Development of a Low-Density and High-Strength Titanium Alloy

Effect of Solution Temperature on Microstructure and Mechanical Properties of Ti–5Al5Mo5V3Cr1Zr Alloy

The Effect of Heat Treatment on the Microstructure and Mechanical Properties of Powder Metallurgy Ti-48Al Alloy

Microstructure evolution, mechanical properties and high temperature deformation of (TiB + TiC)/Ti-3.5Al-5Mo-6V-3Cr-2Sn-0.5Fe titanium alloy

Microstructures and Tensile Properties of a High Strength Β Titanium Alloy Ti5Al4Zr8Mo7V by Near Β Forging and Β-Transus Forging

Effect of Heat Treatment on the Microstructure and Mechanical Properties of Additive Manufactured Ti-6.5Al-2Zr-1Mo-1V Alloy

The effect of heat treatment process on microstructure and mechanical property of large-sized tci8 titanium alloy bar

Effect of Heat Treatment on the Microstructure and Tensile Properties of Deformed Α/β Ti–47Zr–5Al–3V Alloy

EFFECTS OF THERMO-MECHANICAL TREATMENTS ON MICROSTRUCTURE OF Ti-43Al-9V-Y ALLOY