Abstract:The PP alloy was synthesized directly in the reactor with a 4(th) generation Ziegler-Natta catalyst. it is very different from mechanically blended PP alloys, its properties, especially its impact strength,are superior to those of the latter. However,so far the studies on the stucture of this kind of PP alloys have not been reported. The microstructure of a PP alloy was characterized by IR,DSC,and C-13-NMR. The sample was first fractionated and 8 fractions were obtained. The IR analysis showed that the ethylene content of each fraction is different. Except for the first fraction,which is an elastomer, the others are all hard powders at room temperature. Therefore, the fractions above 50 degreesC perhaps are all composed of ethylene-propylene block copolymers. DSC analysis showed that the melting curve of the PP alloy became broadened compared with that of i-PP,and a small peak appeared at 120 degreesC. The extracts of PP alloy in boiling heptane and every fractions of PP alloy all exhibited many small peaks. These peaks demonstrated that the macromolecular chains in PP alloy are composed of ethylene-propylene blocks,whose sequence length are very different. The C-13-NMR spectrum of fraction at 90 degreesC, similar to other fractions at 50 similar to 100 degreesC,also indicated that there are long ethylene sequences in macromolecualr chains of PP alloy. According to the above analysis,a conclusion was reached that the E-P copolymer in PP alloy is composed of EPR and E-P blocks,with different ethylene sequence length. This polydispersity structure in PP alloy made it possess very high impact property.

Temperature Rising Elution Fractionation and Fraction Compositional Analysis of Polybutene-1/Polypropylene In-Reactor Alloys

Temperature rising elution fractionation of polypropylene produced by heterogeneous Ziegler-Natta catalysts

Regulation of Structure and Mechanical Properties of Poly(propylene-Butene) Alloys by Monomer Composition Switching

Temperature Rising Elution Fractionation of Polypropylenes Produced by Heterogeneous Ziegler-Natta Catalysts Containing Different Internal Donors

Temperature Rising Elution Fractionation of Syndiotactic Polypropylene Prepared by Homogeneous and Supported Metallocene Catalysts

Characterization of Microstructure of Polypropylene Alloys

Temperature rising elution fractionation of PP/PE alloy and thermal behavior of the fractions

Application of Temperature Rising Elution Fractionation in Polyolefins

Polypropylene and Ethylene−Propylene Copolymer Reactor Alloys Prepared by Metallocene/Ziegler−Natta Hybrid Catalyst

Microtacticity of Polypropylene Fractions Produced by Different Active Sites of Heterogeneous Ziegler-Natta Catalyst

Structure and Properties of Isotactic Polypropylene/Polybutene-1 In-reactor Alloys

Composition Distributions of Different Particles of A Polypropylene/Poly(Ethylene-Co-Propylene) in Situ Alloy Analyzed by Temperature-Rising Elution Fractionation

Nonisothermal Crystallization of S-Pp Fractions

Separation and identification of ethylene-propylene block copolymer

In Situ Synthesis Of Polybutene-1/Polypropylene Spherical Alloys Within A Reactor With An Mgcl2-Supported Ziegler-Natta Catalyst

Characterization of isotactic polypropylene prepared with dimethylsilyl bis(1-indenyl)zirconium dichloride supported on methylaluminoxane pretreated silica

Influence of Syndiotacticity and Annealing Temperature on the Double Melting Peak Behaviour of Syndiotactic Polypropylene

Preparative temperature rising elution fractionation of polyolefin elastomer and its chain microstructure

Microstructure analysis of polypropylene reactor alloy

Characterization of Intramolecular Composition Heterogeneity of Metallocene-Based and Conventional Ethylene-Butene Copolymers Using Tref/Dsc

Structure and Morphology of Polyethylene/polypropylene In‐reactor Alloys Synthesized by Spherical High‐yield Ziegler–Natta Catalyst