Abstract:Modern Physics Letters B, Ahead of Print. Asymmetric rolling (ASR) is distinguished from conventional symmetric rolling (SR) process as the mismatched rolling speeds of two rolls introduce additional shear deformation to the rolled strips. Friction between the rolls and strip plays an important role in the formation of shear during ASR, which further impacts the microstructures of metallic strips. In this study, finite element (FE) simulations are used to probe the effects of friction in ASR of magnesium (Mg) alloy strips with varied roll speed ratios. The results on shear deformation distributions through the thickness of the strips reveal that the increase of friction coefficient or roll speed ratio induces greater shear deformation simultaneously. It is also found that the roll speed ratio can only promote the shear formation up to a threshold value which is dictated by the friction coefficient, further increasing the mismatch of the roll speeds provides negligible improvement on the plastic deformation of the strips. Experimentally, Mg–1Gd alloy strips are processed by SR and ASR, followed by electropulse treatment (EPT) to induce static recrystallization (SRX). The predictions of the numerical models are verified via EBSD and XRD observations on the grain refinement and texture weakening in Mg–1Gd alloy, which are the direct microstructure consequences of plastic deformations during rolling. At the roll speed ratio of 1.67, the alloy shows a weakened basal texture with an average grain size of 6.0[math][math]m after SRX. Further increasing the roll speed ratio to 5, however, does not enhance the grain refinement or texture weakening significantly.

Multifractal Analyses of Serrated Flow in Friction Stir Processed Al–Mg–Sc Alloy

Characterization of the deformation behaviors associated with the serrated flow of a 5456 Al-based alloy using two orthogonal digital image correlation systems

Experimental investigations on kinetics of Portevin–Le Chatelier effect in Al–4wt.%Cu alloys

Influence of surface pre-deformation on the Portevin-Le Chatelier effect and the related multiscale complexity of plastic flow in an Al-Mg alloy

Multiscale Analysis And Numerical Modeling Of The Portevin-Le Chatelier Effect

A Critical Review on the Portevin-Le Chatelier Effect in Aluminum Alloys

Crystal Plasticity Finite Element Simulation of Grain Evolution Behavior in Aluminum Alloy Rolling

Temporal Statistical Analysis of Serrated Yielding in Al-Cu Polycrystals

High Strain Rate Superplasticity in a Micro-grained Al{Mg{Sc Alloy with Predominant High Angle Grain Boundaries

Friction-mediated tuning of shear deformation and microstructure in asymmetrically rolled Mg–1Gd alloy strips

Micro-nano structure characteristics and texture evolution of the friction stir processed dual-phase Mg Li alloy

The Portevin-Le Chatelier (PLC) effect in an Al-Cu aluminum alloy fabricated by selective laser melting

Investigation on Material Flow and Microstructural Evolution Mechanism in Non-Thinning and Penetrating Friction Stir Welded Al–Cu Aluminum Alloy

Experimental Study and Mechanism Analysis of the Serrated Plastic Instability of Alloy Materials

Formation and Analysis of Amorphous and Nanocrystalline Phases in Al–Cu–Mg Alloy under Friction Stir Processing

Serrated Flow Behavior in 2090 Al–Li Alloy Influenced by Texture and Microstructure

Fracture behavior of a rapidly solidified thin-strip continuous cast AA5182 Al-Mg alloy with the Portevin-Le Chatelier effect under varying strain rates

Influence of Γ′ Precipitates on the Critical Strain and Localized Deformation of Serrated Flow in Ni-based Superalloys

Investigation on Microstructure Evolution of Mg-Gd-Zn-Zr Alloys During Friction Stir Processing by Liquid CO2 Cooling Assisted Stop Action

Microstructure-based Simulation of Constitutive Behaviors in Friction Stir Additive Manufacturing

High Strain Rate Superplasticity in an Al–Mg–Sc–Zr Alloy Processed Via Simple Rolling