Abstract:As regards significance of phase transformations and nature of phases developed as well as their affective role in the physical and mechanical properties and also corrosion resistance of ferritic stainless steel (FSS) welds, this paper wishes to investigate phases identification by means of electron backscattered diffraction (EBSD) analysis and mechanical performance via tensile test. For this goal, the sheets of FSS were prepared for the lap joints and successively, were welded by laser beam welding process under different pulse durations. No welding defects such as porosity, crack, etc., were seen, exhibiting prosperous joining process. Optical microscopy and EBSD corroborated the attendance of low-temperature (LT) and high-temperature (HT) heat-affected zone (HAZ). Fine-grained ferrite, intergranular martensite, as well as carbide precipitates were characterized in the LTHAZ, because of rapid cooling from the zone. Whereas, the HTHAZ was composed of coarse-grained ferrite and intergranular martensite by way of quenching from the zone. Phases characterization could show that the fusion zone (FZ) also had extremely coarsened ferrite and martensite at the grain boundaries. Grain coarsening might be responsible for weak crystallographic texture in this zone. The minimum and maximum microhardness allocated to the FZ and LTHAZ which were 174 5 HV and 261 11 HV, respectively. Founded on the tensile testing, it was apprehended that an increase in the pulse duration from 12 to 15 ms promoted the failure load and energy absorption by almost 13 and 327%, respectively. This was caused by joints strengthening through enhancing the weld penetration. However, an increase in the pulse duration from 15 to 18 ms resulted in degrading the failure load and energy absorption by around 31 and 95%, respectively. This arose from joints weakening due to intensifying grain coarsening phenomenon in the weld zone.

Microstructure and Mechanical Properties of AISI 430 Ferritic Stainless Steel Joints Fabricated by Cold Metal Transfer Welding

Cold Metal Transfer Welding of Ferritic and Austenitic Stainless Steel: Microstructural, Mechanical, and Electrochemical Studies

Microstructure Evolution and Corrosion Behavior of Dissimilar 304/430 Stainless Steel Welded Joints

Influence of Filler Material on the Microstructural and Mechanical Properties of 430 Ferritic Stainless Steel Weld Joints

On the Microstructural Transformations and Mechanical Performance of Laser Beam Welded UNS S43000 Ferritic Stainless Steel

Weld Formation Mechanism and Microstructural Evolution of TC4/304 Stainless Steel Joint with Cu-Based Filler Wire and Preheating

Study on Microstructure and Toughness of Welded Joint of 12%Cr Ferritic Stainless Steel

Microstructure and mechanical property improvement of Ti alloy and stainless steel joint based on a hybrid connection mechanism

Microstructural Evolution and Mechanical Properties of Ti Alloy/Stainless Steel Lap Joints during Cold Metal Transfer Technique with CuSi3 Filler Wire

Microstructure and Mechanical Properties of Dissimilar TC4 Titanium Alloy/304 Stainless Steel Joint Using Copper Filler Wire

Microstructure, properties and fracture failure mechanism of MAG welded joints of four types of stainless steels

Microstructure and corrosion characterization of weld metal in stainless steel and low carbon steel joint under different heat input

Synergistic optimization of microstructure and mechanical properties of AISI 430 ferritic stainless steel via dual-phase zone annealing process

Microstructure and Mechanical Properties of the Joint Fabricated Between Stainless Steel and Copper Using Gas Metal Arc Welding

Microstructure and Performance of Hybrid Laser-Arc Welded 40 Mm Thick 316 L Steel Plates

Insights into microstructure evolution and fracture mechanisms of welded joints of high strength steel patchwork components

Microstructure and mechanical properties of gas metal arc welded CoCrFeMnNi joints using a 308 stainless steel filler metal

Crucial Microstructural Features to Determine the Mechanical Properties of Welded Joints in a Cu-Containing Low-Carbon Low-Alloy Steel After Postweld Heat Treatment

Microstructure Evolution and Mechanical Properties of AISI 430 Ferritic Stainless Steel Strengthened Through Laser Carburization

Effect of Friction Time on Temperature Distribution, Plastic Flow, Microstructure, and Properties in Friction Welding of 1045 Carbon Steel and AISI 430 Ferritic Stainless Steel

Micro Laser Welding of AISI 430 Ferritic Stainless Steel: Mechanical Properties, Magnetic Characterization and Texture Evolution