Abstract:This study delves into the influence of laser welding parameters on the microstructural evolution, surface roughness, and hardness of dissimilar lap joints formed by welding 340BH steel (upper) to cold-rolled pure vanadium (bottom) in an attempt to successfully develop metal membranes by adopting a novel technological route. Specifically, we examined power levels of 0.3 kW and 0.4 kW combined with varying welding speeds (40 mm/s, 50 mm/s, and 60 mm/s). The results indicate that defect-free joints were achievable at the higher welding speed of 60 mm/s. This conclusion is supported by the observed surface roughness profile. Elemental interdiffusion and temperature play pivotal roles in the formation of these dissimilar joints. These factors determine the dimensions of the heat-affected zone (HAZ) and the fusion zone (FZ) under all welding conditions. Notably, the high cooling rates during laser welding hindered the formation of intermetallic phases both in the FZ and at the interface between the metals. Microstructural examination of the HAZ/FZ on the Fe side showed a coarser microstructure when using a power of 0.4 kW, in contrast to the lath martensite observed at 0.3 kW. These observations align with the cooling curve derived from finite element analysis (FEA). FEA was also used to estimate temperature profiles throughout the welded area, and the results were consistent with experimental data. Further microstructural analysis using electron backscattered diffraction (EBSD) revealed a significant phenomenon: the formation of recrystallized grains of vanadium in the HAZ near the FZ on the vanadium side. Microhardness tests, conducted to gauge joint quality, displayed varying hardness levels across the base metal (BM), HAZ, and FZ interfaces. At a power of 0.3 kW, the HAZ displayed greater hardness than the FZ and BM due to the formation of lath martensite. Conversely, at a power setting of 0.4 kW, a reduction in hardness was observed within the HAZ, attributable to coarser ferrite formation.

Micro Laser Welding of AISI 430 Ferritic Stainless Steel: Mechanical Properties, Magnetic Characterization and Texture Evolution

On the Microstructural Transformations and Mechanical Performance of Laser Beam Welded UNS S43000 Ferritic Stainless Steel

Laser spot welding of AISI 304L: metallurgical and mechanical properties

Dissimilar Laser Welding of Austenitic Stainless Steel and Abrasion-Resistant Steel: Microstructural Evolution and Mechanical Properties Enhanced by Post-Weld Heat Treatment

Dissimilar Laser Beam Welding of AISI 420 Martensitic Stainless Steel to AISI 2205 Duplex Stainless Steel: Effect of Post-Weld Heat Treatment on Microstructure and Mechanical Properties

Microstructure Evolution and Mechanical Properties of AISI 430 Ferritic Stainless Steel Strengthened Through Laser Carburization

Laser Welding of Ultra-Fine Grained Steel Ss400

Microstructure and Texture Characterization of Duplex Stainless Steel Joints Welded by Alternating Magnetic Field-Assisted Hybrid Laser-GMAW Welding

A study on effect of laser overlay welding parameters of stainless steel 301 LN: tensile test, microstructure analysis and microhardness evaluation

Microstructural characterization and tensile behavior of Nd:YAG laser beam welded thin high strength low alloy steel sheets

Microstructural Characterization of Laser Weld of Hot-Stamped Al-Si Coated 22MnB5 and Modification of Weld Properties by Hybrid Welding

Microstructural Inhomogeneity in the Fusion Zone of Laser Welds

Effects of Interlaminar Microstructural Inhomogeneity on Mechanical Properties and Corrosion Resistance of Multi-Layer Fiber Laser Welded High Strength Low Alloy Steel

Effect of welding parameters on weld surface roughness, hardness, and microstructure in laser-welded 340BH-steel and pure vanadium

Laser and hybrid laser welding of type 316L(N) austenitic stainless steel plates

Development of Weld Metal Microstructures in Pulsed Laser Welding of Duplex Stainless Steel

Microstructure–Texture–Mechanical Property Correlation in Laser-Welded Dual-Phase and Interstitial-Free Steel Blanks

Morphological Analysis of Laser Surface Texturing Effect on AISI 430 Stainless Steel

Microstructural evolution and mechanical properties of laser-welded joints of medium manganese steel

Microstructure and Mechanical Properties of Pulsed Laser Welded Al/steel Dissimilar Joint

Improvement of inhomogeneity of microstructure and mechanical properties for 316 stainless steel laser-MIG hybrid welded joint assisted by alternating magnetic field