Abstract:This study delves into the influence of laser welding parameters on the microstructural evolution, surface roughness, and hardness of dissimilar lap joints formed by welding 340BH steel (upper) to cold-rolled pure vanadium (bottom) in an attempt to successfully develop metal membranes by adopting a novel technological route. Specifically, we examined power levels of 0.3 kW and 0.4 kW combined with varying welding speeds (40 mm/s, 50 mm/s, and 60 mm/s). The results indicate that defect-free joints were achievable at the higher welding speed of 60 mm/s. This conclusion is supported by the observed surface roughness profile. Elemental interdiffusion and temperature play pivotal roles in the formation of these dissimilar joints. These factors determine the dimensions of the heat-affected zone (HAZ) and the fusion zone (FZ) under all welding conditions. Notably, the high cooling rates during laser welding hindered the formation of intermetallic phases both in the FZ and at the interface between the metals. Microstructural examination of the HAZ/FZ on the Fe side showed a coarser microstructure when using a power of 0.4 kW, in contrast to the lath martensite observed at 0.3 kW. These observations align with the cooling curve derived from finite element analysis (FEA). FEA was also used to estimate temperature profiles throughout the welded area, and the results were consistent with experimental data. Further microstructural analysis using electron backscattered diffraction (EBSD) revealed a significant phenomenon: the formation of recrystallized grains of vanadium in the HAZ near the FZ on the vanadium side. Microhardness tests, conducted to gauge joint quality, displayed varying hardness levels across the base metal (BM), HAZ, and FZ interfaces. At a power of 0.3 kW, the HAZ displayed greater hardness than the FZ and BM due to the formation of lath martensite. Conversely, at a power setting of 0.4 kW, a reduction in hardness was observed within the HAZ, attributable to coarser ferrite formation.

Microstructure–Texture–Mechanical Property Correlation in Laser-Welded Dual-Phase and Interstitial-Free Steel Blanks

Microstructure and Tensile Behavior of Fiber Laser-Welded Blanks of Dp600 and Dp980 Steels

Microstructure Evolution and Mechanical Properties of Laser Welded Dissimilar/Similar Joints Between Medium‐Mn Transformation‐Induced Plasticity Steel and DP980/22MnB5 Steels

Inter-relationship between microstructure evolution and mechanical properties in inertia friction welded 8630 low-alloy steel

Mirostructure and Properties of Laser Welded Joints of Dual Phase and Press-Hardened Steels

Influence of hot forming on microstructure and mechanical properties of laser tailor-welded dissimilar ultra-high-strength steels

Microstructure- and Strain Rate-Dependent Tensile Behavior of Fiber Laser-Welded DP980 Steel Joint

Effects of Interlaminar Microstructural Inhomogeneity on Mechanical Properties and Corrosion Resistance of Multi-Layer Fiber Laser Welded High Strength Low Alloy Steel

Effect of welding parameters on weld surface roughness, hardness, and microstructure in laser-welded 340BH-steel and pure vanadium

Microstructure and Texture Characterization of Duplex Stainless Steel Joints Welded by Alternating Magnetic Field-Assisted Hybrid Laser-GMAW Welding

Microstructure and mechanical properties of friction-stir welded interstitial-free steel using WC tool

Microstructural evolution and mechanical properties of laser-welded joints of medium manganese steel

Microstructure and fracture behavior of laser welded joints of DP steels with different heat inputs

Inhomogeneity of microstructure and mechanical properties in the interlayer regions for narrow gap laser wire filling welding of 316L stainless steel

Micro Laser Welding of AISI 430 Ferritic Stainless Steel: Mechanical Properties, Magnetic Characterization and Texture Evolution

Microstructural characterization and tensile behavior of Nd:YAG laser beam welded thin high strength low alloy steel sheets

Microstructural Influence on Fracture Toughness of IF Steel and DP Steel

On the Microstructural Transformations and Mechanical Performance of Laser Beam Welded UNS S43000 Ferritic Stainless Steel

Tensile resistance, microstructures of intermetallic compounds, and fracture modes of welded steel/aluminum joints produced using laser lap welding

Characterization and modelling of fracture in press-hardened Ductibor® 1000-AS:Usibor® 1500-AS laser-welded blanks

Microstructure and Performance of Hybrid Laser-Arc Welded 40 Mm Thick 316 L Steel Plates