Abstract:Mechanical Performance of traditional gas-shielded arc welded joints of 700 MPa grade microalloyed C-Mn steel cannot meet service requirements. Laser welding, with its characteristic high energy density, is known to improve the welding performance of experimental steels. In the present study, Nb-Ti microalloyed steel with a thickness of 4.5 mm was welded using a 4 kW fiber laser. The microstructure, precipitation, and mechanical properties of the welded joints were studied. The hardness and tensile strength of the welded joints were higher than those of the base metal (BM). The microstructure of the fusion zone (FZ) and coarse grain heat affected zone (CGHAZ) was lath martensite (LM), while the microstructure of the fine grain HAZ and mixed grain HAZ consisted of ferrite and martensite/austenite islands. Although LM was observed in both the FZ and CGHAZ, the hardness and calculated tensile strength of the FZ were lower than those of the CGHAZ, due to a reduction in solid solution strengthening by element loss and the dissolution of high-hardness precipitates in FZ. Most precipitates such as [(Nb,Ti)C and (Nb,Ti)(C,N)] that were present in the BM were dissolved, which led to an increase in C and N in solid solution in the FZ. Thus, the elastic modulus of the FZ was higher than that of the BM. Similarly, the elastic modulus of the CGHAZ was higher than that of the BM due to the segregation of C and N atoms during the welding process. The toughness of the FZ was superior to that of the BM, and the toughness of the HAZ approached 91% of that of the BM. The change in toughness primarily depended on the microstructural refinement, the increase in the fraction of grains with high misorientation, the residual austenite in the FZ and CGHAZ, and the dissolution of coarse precipitates.

Microstructure- and Strain Rate-Dependent Tensile Behavior of Fiber Laser-Welded DP980 Steel Joint

Microstructure and Tensile Behavior of Fiber Laser-Welded Blanks of Dp600 and Dp980 Steels

Microstructure and Mechanical Properties of Fiber Laser Welded QP980 Steel

Temperature Field Simulation and Mechanical Properties of Laser Welded Dp980 Steel Joints

Microstructure and fracture behavior of laser welded joints of DP steels with different heat inputs

Experimental and Numerical Study on Local Mechanical Properties and Failure Analysis of Laser Welded Dp980 Steels

Microstructure and Properties in Dissimilar/similar Weld Joints Between DP780 and DP980 Steels Processed by Fiber Laser Welding

Microstructure Evolution and Mechanical Properties of Laser Welded Dissimilar/Similar Joints Between Medium‐Mn Transformation‐Induced Plasticity Steel and DP980/22MnB5 Steels

Microstructural evolution and mechanical properties of laser-welded joints of medium manganese steel

A comparative study of microstructure and corrosion resistance in DP980 steel joints under different laser welding method

Fiber Laser Welding of 1700-MPa, Ultrahigh-Strength Steel

Mirostructure and Properties of Laser Welded Joints of Dual Phase and Press-Hardened Steels

Microstructure and Mechanical Properties of Laser Welded Dissimilar Joints Between QP and Boron Alloyed Martensitic Steels

Microstructure-Property Correlations in Fiber Laser Welded Nb-Ti Microalloyed C-Mn Steel

Dissimilar Laser Welding/Brazing of 5754 Aluminum Alloy to DP 980 Steel: Mechanical Properties and Interfacial Microstructure

Tensile resistance, microstructures of intermetallic compounds, and fracture modes of welded steel/aluminum joints produced using laser lap welding

Microstructure and Mechanical Properties of Pulsed Laser Welded Al/steel Dissimilar Joint

Research on Microstructure and Mechanical Properties of Fiber Laser Lap Welded Joints of 22Mn B5 Ultra-high Strength Steel

A Study of the Performance of Dissimilar Pulsed-Laser-Welded JSC590R/JAC980YL Steel Joints of Differential Thickness

Microstructure and cyclic hardening/softening behavior of laser welded high strength steel joints under asymmetrical cyclic loading

Effect of laser spot offset on microstructure and properties of laser welded joint of medium Mn/DP980 dissimilar steel