Abstract:The solidification behaviours and microstructural characteristics of both ZA27/SiCp composites and monolithic ZA27 alloy were studied by using differential scanning calorimetry, scanning electron microscopy, transmission electron microscopy, electron probe microanalysis, and X-ray diffraction, It was found that there were differences in the transformation temperature and volume fraction of the phases, although the solidification process was almost identical for the composite and the monolithic alloy. The incorporation of SiC particles in the ZA27 alloy led to slight refinement of primary grains and reduced volume fraction of eutectic-like phase. The SiC particles obstructed Zn diffusion in the residual melt during the formation of proeutectic beta phase, but promoted Zn diffusion from alpha (Al) to eta (Zn) phase during eutectoid transformation. During solidification, Cu was mainly segregated in the final solidification regions; Mg was present not only in the matrix but also on SiC particles; and oxide inclusions were mainly distributed around SiC particles, The matrix microstructure for both materials mainly consisted of primary cores of Al rich alpha + eta eutectoid; beta' phase resulting from the eutectoid transformation of the proeutectic beta phase; and Zn rich alpha + eta eutectoid resulting from the eutectoid transformation of the eutectic-like phase. The SiC particles were mainly distributed around the primary grains, Several new phases based on the Al-Zn-Mg-Cu system and interfacial reaction products, including Al21Fe3Si, Cu5Zn8, Mg6Cu3Al7, MgAl2O4, and amorphous oxide inclusions, were identified in the final solidification regions. The nucleation of both primary alpha phase and eutectic-like alpha + eta phase at the surface of SIC particles and their crystallographic orientation relationships were investigated theoretically and experimentally. No distinct crystallographic orientation relationship between the matrix and SiC has been identified, although the mismatch between (0001)(SiC) and (111)(alpha) was calculated to be as small as 7.6%.

In Situ Surface Composites of (mg2si+si)/za27 Fabricated by Centrifugal Casting

In-situ (Mg2Si+Si)/Zn matrix composite fabricated by centrifugal casting

The Centrifugally Cast Zn-Al-Mg-Si Alloys and Their in Situ Surface Composites

Centrifugally Cast Zn–27Al–xMg–ySi Alloys and Their in Situ (mg2si + Si)/ZA27 Composites

Microstructure and properties of in-situ Zn-Al-Si surface composites prepared by centrifugal casting

Functionally graded Zn-AI-Si in-situ composites fabricated by centrifugal casting

High-Resolution Electron Microscope Observation of Interface Microstructure of A Cast Al-Mg-Si-Bi-Pb(6262)/Al2o3p Composite

In Situ （mg2si＋mgo）/mg Composites Fabricated from AZ91-Al2（SiO3）3 with Assistance of High-Energy Ultrasonic Field

Fabrication and Formation Mechanism of in Situ AlN and Mg2Si Particles-Reinforced Mg Matrix Composites

In-Situ Fabrication And Properties Of Mg2si/Az91d Magnesium Matrix Composites

Microstructure evolution of SiC p /ZM6 (Mg–Nd–Zn) magnesium matrix composite in the semi-solid state

Fabrication and properties of in situ (Al3Zr + Al2O3)p/A356 composites cast by permanent mould and squeeze casting

Mechanical properties, dry sliding wear resistance, and microstructural characterization of in-situ Al-17Si-Al3Zr/Al2O3 FG-composite synthesized via vertical centrifugal casting technique

Microstructure and Mechanical Properties of Mg 2 Si/AZ91 Composites In Situ Synthesized by Using Silica Fume as the Si Source

Investigations on Microstructure, Mechanical Properties and Tribological Behavior of In-Situ Mg2Si Particles Reinforced AZ91 Composites

In situ surface composite and gradient material of Al-Si alloy produced by electromagnetic force

Microstructure and Mechanical Properties of Sicp/Mg-Zn-Ca Composites Fabricated by Stir Casting

Solidification and microstructure of ZA27/SiCp composite fabricated by mechanical-electromagnetic combination stirring process

Preparation and Mechanical Properties of in Situ Submicron MgAl2O4p/6061Al Composites from Al–Mg–SiO2 System

Magnesium Matrix Nanocomposites Fabricated by Ultrasonic Assisted Casting

Microstructure and mechanical properties of ZrB2-SiC composites fabricated by the centrifugal gel casting