Abstract:Selective laser melting (SLM), as a rapid prototyping technology, has been widely used to manufacture high-performance metal components with complex structures, which vitally provides a broad platform for the development and application of magnesium alloys. However, the poor laser formability of magnesium alloys has deleterious consequences in the application of SLM processing. This paper discusses the defect formation mechanisms during the SLM process and summarizes characteristics in terms of mechanical properties, oxidation and corrosion resistance. Current optimization schemes are reviewed from both macro and micro perspectives. Firstly, the relationship between process parameters and formability and material properties is clarified, and advanced optimization methods of the design of experiments, physical models, and machine learning are evaluated. Secondly, the effects of alloying elements, composite reinforcement, and post-treatment on the microstructure and properties of the SLMed magnesium alloy are reviewed. Finally, the future application development prospects are envisaged based on the comprehensive review. This work is significantly helpful to a better scientific understanding of SLMed magnesium alloy and puts forward some meaningful guiding opinions for the future work of magnesium alloy manufacturing. A dual-textured wrought Mg-6.5 Zn (wt.%) alloy with limited yield asymmetry (compressive yield strength / tensile yield strength: 0.90) is reported. Approximately 80% of the grains present the standard texture of wrought Mg alloys while the grain orientation is rotated by ≈ 90o perpendicularly to the c axis in the remaining 20%. The deformation mechanisms responsible for this behavior are analyzed on samples deformed in tension and compression up to different strains. Compressive deformation of the grains with the standard texture is accommodated by 〈a〉 basal slip and extension twinning while tensile deformation promotes 〈a〉 basal and non-basal 〈a〉 prismatic and 〈a〉 pyramidal slip, leading to the typical yield asymmetry. However, the rotated grains present the opposite (and much stronger) yield asymmetry because tensile deformation is absorbed by 〈a〉 basal slip and extension twinning while compression deformation requires 〈a〉 basal slip and compression twinning. Thus, the contribution of the 20% rotated grains to the overall mechanical behavior leads to (almost) similar values of the yield strength in tension and compression. This work provides a physical understanding of the deformation behavior of dual-textured Mg alloys, that can be used to develop novel dual-textured Mg alloys with limited yield asymmetry. A novel Ti 40 Nb 30 Mo 30 –C refractory complex concentrated alloy (RCCA) reinforced with in-situ (Ti, Nb)C carbide was fabricated via mechanical alloying (MA) and hot press sintering (HPS). The results showed that the alloy consisted of the BCC crystal-structured solid solution phase (TNM phase) and FCC crystal-structured carbide (Ti, Nb)C with submicron grain sizes of 0.79 μm and 0.62 μm, respectively. The ultra-fine microstructure benefitted from the inhabitation of in-situ (Ti, Nb)C on grain growth. The ab-initio calculations were conducted to study the formation process of in-situ composite carbide (Ti, Nb)C. Here, the lightweight alloy with a density of 7.04 g/cm 3 exhibited promising compressive mechanical properties, such as yield strength of 2550 MPa at room temperature (RT), 1508 MPa at 800 °C, and 485 MPa at 1000 °C. According to the deformation microstructures at RT and 1000 °C, the dislocation-dominated deformation mechanism in TNM phase was invariable at different temperatures. A brittle-to-ductile translation of (Ti, Nb)C was found to happen at around 1000 °C supported by the stress-strain curve and TEM observation. The excellent mechanical properties of the alloy were attributed to the grain boundary strengthening and the strengthening effect of (Ti, Nb)C that hindered the movement of dislocations. The strategy that incorporating in-situ carbides into light RCCA system could broaden and inspire the design of lightweight and high-strength materials. In this study, SiC/Al–Cu nanocomposites were fabricated via simultaneous solid-state alloying of Cu and dispersing of SiC nanoparticles in Al matrix, for the first time. We showed that a complete solid solution of Cu (4.5 wt%) and a uniform dispersion of dense (up to 15 vol%) SiC nanoparticles in Al matrix can be successfully achieved, by accumulative roll-bonding (ARB) of pure Al, Cu and SiC nanoparticles to high cycles. The as-prepared SiC/Al–Cu nanocomposites exhibited excellent mechanical properties at room temperature and at 300 °C. The microhardness and tensile strength of the SiC/Al–Cu nanocomposites were both significantly increased by incorporating Cu solutes and dense SiC nanoparticles, surpassing those -Abstract Truncated-

Synthesis and Characterization of Mg-Al-Zn Alloy-Based Bimodal Hybrid Composites with SiC and TiO2

Influence of hybrid reinforcements on the mechanical properties and morphology of AZ91 magnesium alloy composites synthesized by ultrasonic-assisted stir casting

Exploring the mechanical and structural properties of B 4 C/ZrO 2 strengthened Al-Mg-Cr alloy hybrid composites

Synthesis and Experimental Investigations of Tribological and Corrosion Performance of AZ61 Magnesium Alloy Hybrid Composites

Microstructure and Mechanical Properties of Hybrid AZ91 Magnesium Matrix Composite with Ti and SiC Particles

Implications of SiC/Al2O3 Reinforced Al-Mg-Zn Alloy Hybrid Nano Composites Using Vacuum Sintering Method

Selective laser melting of magnesium alloys: Necessity, formability, performance, optimization and applications

Microstructural, hardness, and wear properties of Mg 2 Si-reinforced Al matrix in-situ composites produced by low superheat casting

Effect of Microstructure on Mechanical Behaviors of Al6061 Metal Matrix Composite Reinforced with Silicon Nitride (Si3N4) and Silicon Carbide (SiC) Micro Particles

Microstructure and properties of a HIP manufactured SiC p reinforced high alloyed Al–Zn–Mg–Cu–Zr–Ti aluminum matrix composite

Magnesium Based Hybrid Nanocomposites: An Insight into Nanoparticle Effects on the Microstructure and Mechanical Properties

Mechanical and wear behavior of Al 7075/Al2O3/SiC/mg metal matrix nanocomposite by liquid state process

Processing, microstructure and ageing behavior of in-situ submicron TiB2 particles reinforced AZ91 Mg matrix composites

Effect of Heat Treatment on Microstructure and Mechanical Properties of Squeeze Cast n SiCp/AZ91D Magnesium Matrix Composites

Investigation of Microstructural and Mechanical Properties of Magnesium Matrix Hybrid Composite

Experimental investigation on the mechanical performance of the Al2O3 and ZrO2 added Al-Mg-Si alloy for structural applications

Spectroscopic Characterization and Properties of Mg2B2O5w/AZ91D Magnesium Composites

Synergistic strengthening mechanism and microstructural evolution of Al-Zn-Mg-Cu/ Al2O3/Y2O3 hybrid nanocomposite via mechanical alloying and hot pressing

Characterization on properties of Al7050/TiC/BN hybrid metal matrix composite

Microstructure Evaluation, Quantitative Phase Analysis, Strengthening Mechanism and Influence of Hybrid Reinforcements (β-SiCp, Bi and Sb) on the Collective Mechanical Properties of the AZ91 Magnesium Matrix

Silicon Carbide Particle Enriched Magnesium Alloy (AZ91) Composite: Physical, Microstructural and Mechanical Studies