Abstract:Carbon dots enhanced ultra‐low‐density fluorescence proppants with both high‐compressive strength and anti‐deformation ability. The polymer ultra‐low‐density proppants are critical to the development of slick‐water fracture technology, but which were prone to obvious deformation under high pressure in the fractures. To increase the stiffness of the styrene‐divinylbenzene copolymer (SDB) and obtain desired ultra‐low‐density (ULD) proppants, carbon dots (CDs) were introduced in‐situ considering their characteristics as the zero‐dimensional carbon nanomaterial. Taking the compressive strength and axial deflection, and so forth into consideration, the synthesis conditions of CDs modified SDB microspheres (CDs‐SDBs) were optimized. Taking the graphite modified SDBs (MG‐SDBs) as a reference, the density of CDs‐SDBs did keep almost constant at about 1.1800 ~ 1.1899 g·cm−3 with the increase of CDs amount. The CDs‐SDBs not only possess high‐peak pressure (41.5 N) but also minute axial deflection (0.090 mm). The advantages of CDs‐SDBs over MG‐SDBs become even more pronounced under higher pressure, which can withstand closure pressure of 80 MPa with a small crush ratio of 4.47%. CDs‐SDBs exhibit significant photoluminescence performances with maximum excitation and emission wavelengths of 634 nm and 554 nm. Highlights CDs‐SDBs as ULD proppants with high strength and anti‐deformation were developed. Advantages of CDs‐SDBs become more pronounced under high‐closure pressure. With increasing of CDs amount, apparent density of CDs‐SDBs keep almost constant. Axial deflection of CDs‐SDBs is only 0.09 mm under 41.5 N. The crush ratio is only 4.47% under 80 MPa closure pressure.

Preparation and Characterization of Polymeric Ultra-Low-Density Proppants: Epoxy/Phenolic Resin-Coated Polystyrene/Graphite Microspheres

Optimal Preparation and Characterization of Poly(urea–formaldehyde) Microcapsules

Facile and Controllable Preparation of Poly(St-co-MMA)/FA Microspheres Used as Ultra-Lightweight Proppants

Fabrication of Low-density Heat-Resistance Polystyrene/Carbon Black Composite Microspheres Used as Hydraulic Fracturing Proppant

Constructing low-cost and high-strength ultra-low-density proppants based on the modification of activated carbon framework with in-situ hydrolyzed silane

Preparation and characterization of a self-suspending ultra-low density proppant

Hydrophobic epoxy resin coated proppants with ultra-high self-suspension ability and enhanced liquid conductivity

A Study on a New Type of High-Performance Resin-Coated Sand for Petroleum Fracturing Proppants

Progress of Polymer Application in Coated Proppant and Ultra-Low Density Proppant

Shaly detritus embedded epoxy-resin coated proppants

Preparation of Poly(methyl Methacrylate)/ultrafine CaCO3 Composite Particles by In-Situ Dispersion Polymerization

Mechanical Properties of Polyurethane Foams Prepared from Liquefied Corn Stover with PAPI.

Preparation of low density, high-strength, strong hydrophobic particles (LHSPs) and its application as oil fracturing proppant

Carbon dots enhanced ultra‐low‐density fluorescence proppants with both high‐compressive strength and anti‐deformation ability

Preparation of Polystyrene/Sio2 Composite Nanoparticles Bearing Sulfonic Groups on the Surface Via Emulsion Copolymerization Using A Polymerizable Emulsifier

Development of the epoxy resin phase change proppant based on the Pickering emulsification technology

Insight into thermo-mechanical enhancement of polymer nanocomposites coated microsand proppants for hydraulic fracturing

Preparation and Performance Evaluation of Self-Cementing Nanoscale Polymeric Microspheres with Salt and Temperature Tolerance

Preparation and Properties of Lightweight Amphiphobic Proppant for Hydraulic Fracturing

Preparation and characterization of high-performance ceramic proppant from recycling utilization of oil-based drilling cuttings pyrolysis residues

Synthesis of porous polyurea microspheres for matting coating