Abstract:At present, the most common type of SOFC is anode-supported SOFC (AS-SOFC), in which the cell is mechanically supported by the thick fuel electrode layer. Recently, Metal-supported SOFCs (MS-SOFCs) have attracted attention because of their potential for low cost and high mechanical robustness. However, the fabrication process of MS-SOFCs has not been established. The mechanical behavior of the cells under high temperature operation has not been clarified. In this study, we fabricated prototype MS-SOFCs using the plasma spray method. The cell was tested by electrochemical measurements, residual stress measurements, and SEM/EDX to clarify the mechanical behavior of MS-SOFCs under high temperature operation. The layers of anode (NiO-YSZ), electrolyte (LSGM9182), and cathode (LSCF6428) were formed on a metal substrate (SUS430) by atmospheric pressure plasma spraying (APS) to fabricate a single cell of MS-SOFC. Open circuit voltage, AC impedance, and I-V measurements were performed at 600°C, 650°C, and 700°C. The residual stress of LSGM9182 electrolyte was evaluated by cosα method [1] under the cell operation condition using specially designed chamber. The MS-SOFC with thicker electrode layers showed the much lower OCV than that of theoretical. In addition, the electrolyte had vertical cracks between cathode and anode after the 2nd thermal cycle. However the MS-SOFC with thinner electrode layers showed the higher OCV, which was nearly theoretical value, and much better I-V characteristics than the cell with thicker electrodes. Electrochemical impedance measurement revealed the plasma sprayed electrodes showed acceptable performance even though its microstructure was not optimized. The residual stress of LSGM electrolyte in the cell did not change so much during the cell operation. This might be caused by existence of small cracks in the electrolyte layer. This research was financially supported by NEDO. [1] K.Tanaka, Journal of the Society of Materials Science,japan,vol.66,No.7 (2017) 479-487

Mechanical Property and Deformation Behavior of SOFCs

Towards Feasible Temperature Management and Thermo-Mechanical Stability of Carbon-Assisted Solid Oxide Electrolysis Cell

Real-time deformation and stress response of the planar SOFC during sintering

A High-Strength Solid Oxide Fuel Cell Supported by an Ordered Porous Cathode Membrane

Electrochemical Performance and Mechanical Stress Evaluation of Metal-Supported Solid Oxide Fuel Cells Fabricated By Plasma Spray Method

Fabrication and Properties of Anode-Supported Solid Oxide Fuel Cell

Simulation and Analysis of Sintering Warping and Thermal Stress for a Cermet Half-Cell of Solid Oxide Fuel Cells

Tape Casting of Bilayered Anode Supports and Electrochemical Performance of SOFCs Based on Them

Electrochemical Property of Multi-Layer Anode Supported Solid Oxide Fuel Cell Fabricated Through Sequential Tape-Casting and Co-Firing

Electrochemical performance and redox stability of solid oxide fuel cells supported on dual-layered anodes of Ni-YSZ cermet and Ni–Fe alloy

Fabrication and Characterization of Large Size Anode Substrate of Solid Oxide Full Cell

Fabrication and Performance of Ceramic Anode-Supported Solid Oxide Fuel Cells

Characteristic simulation with various anode support thicknesses of membrane electrode assembly in SOFC

Performance and Optimization of Ni/3 Mol% Y2O3-ZrO2 Anode Supported SOFC

Durability Study of Anode-Supported SOFC with Large-Area Fabricated By 4-Layer Sequential Co-Lamination and GDC Co-Firing Process

Fabrication of Electrode Supporters for Solid Oxide Fuel Cells by Tape Calendaring Process

Mechanical Properties of La0.6Sr0.4Co0.2Fe0.8O3-d Fuel Cell Electrodes

Fabrication and Characterization of Composite Electrolyte for Intermediate-Temperature SOFC

Long-term thermo-mechanical performance evolution of a 15-cell solid oxide fuel cell stack

Fabrication of tubular NiO/YSZ anode-support of solid oxide fuel cell by gelcasting

High-performance cathode-supported SOFCs prepared by a single-step co-firing process