Abstract:Objectives To investigate transient thermal stresses that developed in 3Y-TZP green compacts during speed sintering. Methods A total of 312 disc-shaped green compacts (Ø17.1 ×1, 1.5, 2, 2.5, 3 mm) were cold-isostatically pressed from 3Y-TZP powder (Zpex, Tosoh Corp.) for speed sintering studies as well as compositional analysis and biaxial flexural strength measurements (both at room temperature and following heating at 90 °C/min to 500 °C). Flexural strength was determined using the piston-on-3-ball method. Phase assemblies were analyzed using the X-ray diffraction method. Effects of heating/cooling rates on transient stresses were investigated by conducting definitive sintering studies to determine the threshold for fracture. Finite element analysis (FEA) was used to validate the experimental findings using measured thermomechanical properties. Results The bulk and relative density of the green compact were 2.95 ± 0.03 g/cm 3 and 48.52% ± 0.45%. The flexural strength was drastically decreased from 10.3 ± 0.4 MPa to 1.09 ± 0.07 MPa following heating at 90 °C/min to 500 °C. The monoclinic and tetragonal contents were 54.9% and 45.1%, respectively. The threshold for fracture was located at 500 °C during the first heating stage with a 90 °C/min heating rate in specimens of 2.5 mm thickness or greater. No fractures occurred in the second heating stage and cooling phase. The FEA estimated that the principal transient tensile stress was ∼1.14 MPa at 500 °C during the heating phase, which exceeded the corresponding flexural strength (1.09 ± 0.07 MPa). Significance Advanced FEA methods are an accurate and efficient tool to analyze the history of transient stresses during sintering of ceramic dental restorations.

Prediction of Sintering Process for Zro2 Ceramics Based on Master Sintering Curve Theory and Its Expansion

Densification Evolution of TiO2 Ceramics During Sintering Based on the Master Sintering Curve Theory

Thermally-insulated ultra-fast high temperature sintering (UHS) of zirconia: A master sintering curve analysis

Numerical and Experimental Analysis of Anisotropic Shrinkage During Sintering

Application of Master Sintering Curve Theory to Predict and Control the Sintering of Nanocrystalline TiO<sub>2</sub> Ceramic

Prediction of Microstructure Evolution for Micron Α-Al_2o_3 During Pressureless Sintering at Constant Heating Rates

Influence of Sintering Temperatures on Material Properties and Corresponding Milling Machinability of Zirconia Ceramics

Densification, Mechanical and Thermal Properties of ZrC1− Ceramics Fabricated by Two-Step Reactive Hot Pressing of ZrC and ZrH2 Powders

Pressureless Sintering of ZrC-based Ceramics by Enhancing Powder Sinterability

Study on ZrB2-SiC Prepared by Field Assisted Sintering

Sintering mechanisms of partially stabilized zirconia (TZ3Y) with ZnO and Co3O4 as sintering additives

Cold Sintering Process for 8 Mol%y2o3-Stabilized ZrO2 Ceramics

Compacting and Sintering Behavior of Nano ZrO 2 Powders

Influence of bismuth oxide as a sintering aid on the densification of cold sintering of zirconia

[Influence of Compaction Pressure and Pre-Sintering Temperature on the Machinability of Zirconia Ceramic].

Densification Kinetics of Multi-Doped Zirconia Ceramic Body with Organic Coating Powders

Initial sintering mechanism and additive effect in zirconia ceramics

Effect of Sintering Temperature on Compressive Strength of Porous Yttria-Stabilized Zirconia Ceramics

Zr 1 _ YW 2 O 8-ƒÂ ( x = 0 . 000 . 02 ) Ceramic Using Reactive Sintering

Transient thermal stresses developed during speed sintering of 3 mol% yttria-stabilized tetragonal zirconia polycrystals

A generalized master sintering curve based on nucleation-limited densification kinetics