Abstract:In the past decades, Zirconia (ZrO2) has emerged as a promising technical ceramic, both as high temperature structural material and electrolyte for fuel cells, etc. The traditional synthesis of ZrO2 with spark plasma sintering (SPS) usually requires a sintering temperature as high as 1200 °C. General interest in lowering the sintering temperature to reduce energy consumption and thermal stresses has led to research on two promising routes – cold sintering via temperature-dependent chemical reactivity and sintering aids, which facilitates mass transport and improves densification. Here we combine both by developing a single-step sintering process benefitting from both water vapor through the in-situ conversion of Zr(OH)4 to ZrO2 and liquid phase Bi2O3 as a sintering aid. The resultant ZrO2 has a relative density above 80% with a sintering temperature as low as 900 °C, significantly higher than that of ZrO2 without sintering aids, which had a relative density of 54%, both sintered at 50 MPa. The dependence of porosity of sintered samples as a function of sintering pressure (range: 50 MPa–300 MPa) and temperature (range 400 °C–1200 °C) is mapped out as guidance for further material property design. A linear relationship between hardness and relative density was found, with a maximal hardness of 6.6 GPa achieved in samples with 30% porosity. In addition to sintered density, phase stabilization of tetragonal ZrO2 is enhanced at sintering temperature of 900 °C with water vapor and Bi2O3, respectively.

Effect Of Sintering Temperature On Structures And Properties Of High Quality Zirconia Ceramics Under Oscillatory Pressure

Effect of Oscillatory Pressure on the Sintering Behavior of ZrO2 Ceramic

An Oscillatory Pressure Sintering of Zirconia Powder: Densification Trajectories and Mechanical Properties

Preparation of Zirconia Ceramics with High Density and Fine Grains by Oscillatory Pressure Sintering

Microstructure and Mechanical Properties of Zirconia Ceramics Consolidated by a Novel Oscillatory Pressure Sintering

An Oscillatory Pressure Sintering of Zirconia Powder: Rapid Densification with Limited Grain Growth

Hydrothermal Aging of Zirconia Ceramics Consolidated by Oscillatory Pressure Sintering

Microstructure and Mechanical Properties of ZTA Composites Fabricated by Oscillatory Pressure Sintering

A Novel Oscillatory Pressure-Assisted Hot Pressing For Preparation Of Highperformance Ceramics

Improved Mechanical Properties of 3YSZ Ceramics Prepared by Pressure-less Sintering Assisted by Cold Sintering under Mild Conditions

Optimization of microstructure and mechanical properties of oscillatory pressure sintered ZrO<sub>2</sub>-Al<sub>2</sub>O<sub>3</sub>-SiCp ceramics

Zirconia Ceramics Consolidated by Oscillatory Pressure Sintering and Subsequent Carburization

Optimization of microstructure and mechanical properties of oscillatory pressure sintered ZrO2–Al2O3-SiCp ceramics

Optimum Sintering Temperature of High Quality Silicon Nitride Ceramics under Oscillatory Pressure

Microstructural evolution and mechanical properties of ZrO<sub>2</sub> (3Y)-Al<sub>2</sub>O<sub>3</sub>-SiC(<sub>w</sub>) ceramics under oscillatory pressure sintering

Preparation of Zirconia Ceramics by Spark Plasma Sintering Technique and Their Mechanical Properties

Sintering behavior and mechanical properties of β-SiC ceramics under oscillatory pressure

Fabrication of ZrO2 whisker modified ZrO2 ceramics by oscillatory pressure sintering

Oscillatory pressure sintering of binderless tungsten carbide

Effect of Sintering Temperature on Compressive Strength of Porous Yttria-Stabilized Zirconia Ceramics

Influence of bismuth oxide as a sintering aid on the densification of cold sintering of zirconia