Abstract:Fully dense ceramics with retarded grain growth can be attained effectively at relatively low temperatures using a high-pressure sintering method. However, there is a paucity of in-depth research on the densification mechanism, grain growth process, grain boundary characterization, and residual stress. Using a strong, reliable die made from a carbon-fiber-reinforced carbon (Cf/C) composite for spark plasma sintering, two kinds of commercially pure α-Al2O3 powders, with average particle sizes of 220 nm and 3 μm, were sintered at relatively low temperatures and under high pressures of up to 200 MPa. The sintering densification temperature and the starting threshold temperature of grain growth (Tsg) were determined by the applied pressure and the surface energy relative to grain size, as they were both observed to increase with grain size and to decrease with applied pressure. Densification with limited grain coarsening occurred under an applied pressure of 200 MPa at 1050 °C for the 220 nm Al2O3 powder and 1400 °C for the 3 μm Al2O3 powder. The grain boundary energy, residual stress, and dislocation density of the ceramics sintered under high pressure and low temperature were higher than those of the samples sintered without additional pressure. Plastic deformation occurring at the contact area of the adjacent particles was proved to be the dominant mechanism for sintering under high pressure, and a mathematical model based on the plasticity mechanics and close packing of equal spheres was established. Based on the mathematical model, the predicted relative density of an Al2O3 compact can reach ∼80 % via the plastic deformation mechanism, which fits well with experimental observations. The densification kinetics were investigated from the sintering parameters, i.e., the holding temperature, dwell time, and applied pressure. Diffusion, grain boundary sliding, and dislocation motion were assistant mechanisms in the final stage of sintering, as indicated by the stress exponent and the microstructural evolution. During the sintering of the 220 nm alumina at 1125 °C and 100 MPa, the deformation tends to increase defects and vacancies generation, both of which accelerate lattice diffusion and thus enhance grain growth.

Sintering Kinetics Involving Densification and Grain Growth of 3D Printed Ce–ZrO2/Al2O3

Sintering kinetics of cerium-stabilised tetragonal zirconia

Effects of Al2O3 doping on the microstructural evolution and densification process of AZO targets

Fabrication of High-Performance Al2O3-ZrO2 Composite by a Novel Approach That Integrates Stereolithography-Based 3D Printing and Liquid Precursor Infiltration

Densification mechanism of stereolithographical dense Si3N4 ceramics with CeO2 as sintering additive by field assisted sintering

The preparation of ZrO2-Al2O3 composite ceramic by SLA-3D printing and sintering processing

Sinterability of ZrSiO4/α-Al2O3 Mixed Powders

Densification mechanism and microstructure characteristics of nano- and micro- crystalline alumina by high-pressure and low temperature sintering

Impact of Sintering Aid Type and Content on the Mechanical Properties of Digital Light Processing 3D-Printed Si3N4 Ceramics

The Effect of Nano-Al<sub>2</sub>O<sub>3</sub> on Sintering Behavior and Mechanical Property of ZrO<sub>2</sub> Ceramics

The Effect of Nano-Al2O3 on Sintering Behavior and Mechanical Property of ZrO2 Ceramics

Stability properties and microstructure properties of microwave-sintered CeO2 doped zirconia ceramics

Pressureless sintering and properties of additively manufactured ZrB2–SiC

Influence of sintering temperature and CVI time on mechanical properties of 3D-printed alumina ceramics

Comparison of sintering behavior and reinforcing mechanisms between 3Y-TZP/Al2O3(w) and 12Ce-TZP/Al2O3(w) composites: Combined effects of lanthanide stabilizer and Al2O3 whisker length

Influence of SiO2 addition on the sintering behavior and kinetics of fine-sized α-Al2O3 nanoparticles

Effect of Holding Time During Sintering on Microstructure and Properties of 3D Printed Alumina Ceramics

Achieving high-strength, high-porosity and relatively low-shrinkage in extrusion-based 3D printed ZrO 2 ceramics by adjusting CaCO 3 addition and sintering temperature

Sintering kinetics involving grain growth and densification of Mg-PSZ nanopowders

The Rising Crack Resistance Curve Behavior and Mechanism of La2O3 Doped Zirconia Toughened Alumina Composites Prepared Via Vat Photopolymerization Based 3D Printing

Sintering Behavior and Mechanical Properties of Alumina-Coated Zirconia Ceramics