Abstract:Molten lead (Pb) and its alloys (PbBi and PbLi) are of immense interest for various nuclear engineering applications, including but not limited to advanced Lead-cooled Fast Reactors (LFRs), tritium Breeding Blankets (BBs) of fusion power plants and spallation targets for Accelerator-Driven Systems (ADS). Owing to their attractive thermophysical properties, these advanced fluids assert their candidacy to address the critical requirements of neutron multiplication, neutron moderation, high temperature coolants and tritium breeders, enabling the operation of next generation nuclear systems at high temperatures with better efficiencies. However, for numerous reasons such as a compromise of structural integrity at the heat transfer interface, presence of an inert cover gas during charging of molten metal in the loop, and the fusion fuel cycle itself may lead to molten metal-gas two-phase flows with high density ratios. At present, no effective diagnostics exist to detect such operational and accidental occurrences in high temperature molten metal systems resulting in a severe lack of relevant experimental studies. To address these limitations and to advance the current understanding toward two-phase regimes in high temperature Pb-based melts, the present work focuses on the design and assembly aspects of an electrical conductivity-based two-phase detection sensor array, utilizing high purity α-Al 2 O 4 coatings with AlPO 4 binder as electrical insulation layers. This paper discusses the design considerations, thermal analysis, systematic selection of structural/functional components along with preliminary results from the probe performance tests in very high temperature (600°C) static molten Pb column for real time detection of argon gas bubbles rising within the melt. Quantitative estimations of time-averaged void fraction, average bubble impaction frequency and average bubble residence time are presented from the preliminary experimental investigations.

Contact Angle Measurement of Molten Lead-Lithium on Silicon Carbide Surfaces

Experimental Investigation on Contact Angles of Molten Lead–Lithium on Silicon Carbide Surface

Laminar mixed convection heat transfer of SiC-EG nanofluids in a triangular enclosure with a rotating inner cylinder: simulations based on the measured thermal conductivity and viscosity

Consideration of Alumina Coating Fabricated by Sol-gel Method as MHD Coating against PbLi

Electrical insulation test of alumina coating fabricated by sol–gel method in molten PbLi pool

Consideration of Alumina Coating Fabricated by Sol–Gel Method for PbLi Flow

Ultrasonic Doppler Velocimetry Experiment of Lead-Lithium Flow with Oroshhi-2 Loop

ACOUSTIC PROPERTIES OF Pb-17Li ALLOY FOR ULTRASONIC DOPPLER VELOCIMETRY

Experimental Measurements for the Effective Thermal Conductivity of Pebble Beds with Uncertainty Analysis

Velocity Profile Measurement of Lead-Lithium Flows by High-Temperature Ultrasonic Doppler Velocimetry

MHD Pressure Drop Measurement of PbLi Flow in Double-Bended Pipe

Design, fabrication and validation of an electrical conductivity principle based two-phase detection sensor array for molten lead (Pb) based heavy metal coolants up to 600^∘C

MEASUREMENTS OF FINE STRUCTURES IN THE LEAD-BISMUTH EUTECTIC ALLOY MELTS BY DIFFERENTIAL SCANNING CALORIMETRY

Design and Research on the Measurement Platform of the Effective Thermal Conductivity for Li4SiO4 and Li2TiO3 Pebble Bed

Development and validation of electrical-insulating Al2O3 coatings for high-temperature liquid PbLi applications

A sessile drop approach for studying 4H-SiC/liquid silicon high-temperature interface reconstructions

Experimental Investigation on the Leidenfrost Phenomenon of Droplet Impact on Heated Silicon Carbide Surfaces

ICONE19-43372 Numerical Simulation of Opposing Mixed Convection Heat Transfer of Lithium-Lead in a Vertical Square Channel with Heat Source

Numerical Investigation of Buoyant Effect on Flow and Heat Transfer of Lithium–Lead Eutectic in DFLL–TBM

Wetting and Interfacial Behavior of Molten Al on Mo-Ni(Co)-Si Coated SiC Ceramic

Numerical Simulation of Agglomeration Characteristics of Liquid Lead-Bismuth Eutectic (LBE) Impurity Particles