Abstract:Molten lead (Pb) and its alloys (PbBi and PbLi) are of immense interest for various nuclear engineering applications, including but not limited to advanced Lead-cooled Fast Reactors (LFRs), tritium Breeding Blankets (BBs) of fusion power plants and spallation targets for Accelerator-Driven Systems (ADS). Owing to their attractive thermophysical properties, these advanced fluids assert their candidacy to address the critical requirements of neutron multiplication, neutron moderation, high temperature coolants and tritium breeders, enabling the operation of next generation nuclear systems at high temperatures with better efficiencies. However, for numerous reasons such as a compromise of structural integrity at the heat transfer interface, presence of an inert cover gas during charging of molten metal in the loop, and the fusion fuel cycle itself may lead to molten metal-gas two-phase flows with high density ratios. At present, no effective diagnostics exist to detect such operational and accidental occurrences in high temperature molten metal systems resulting in a severe lack of relevant experimental studies. To address these limitations and to advance the current understanding toward two-phase regimes in high temperature Pb-based melts, the present work focuses on the design and assembly aspects of an electrical conductivity-based two-phase detection sensor array, utilizing high purity α-Al 2 O 4 coatings with AlPO 4 binder as electrical insulation layers. This paper discusses the design considerations, thermal analysis, systematic selection of structural/functional components along with preliminary results from the probe performance tests in very high temperature (600°C) static molten Pb column for real time detection of argon gas bubbles rising within the melt. Quantitative estimations of time-averaged void fraction, average bubble impaction frequency and average bubble residence time are presented from the preliminary experimental investigations.

Consideration of Alumina Coating Fabricated by Sol–Gel Method for PbLi Flow

Consideration of Alumina Coating Fabricated by Sol-gel Method as MHD Coating against PbLi

Electrical insulation test of alumina coating fabricated by sol–gel method in molten PbLi pool

Corrosion behavior and failure mechanism of amorphous Al2O3 coating at high-temperature LBE

Development and validation of electrical-insulating Al2O3 coatings for high-temperature liquid PbLi applications

Fabrication Aspects and Performance Characterization of α-Al2O3/ALPO4 Based Sandwich Configuration Flow Channel Inserts and Coatings for High Temperature Liquid Metal Applications

Design, fabrication and validation of an electrical conductivity principle based two-phase detection sensor array for molten lead (Pb) based heavy metal coolants up to 600^∘C

A new preparing method and performances of FeAl/Al2O3 tritium permeation barrier

Contact Angle Measurement of Molten Lead-Lithium on Silicon Carbide Surfaces

Sol–gel prepared Al2O3 coatings for the application as tritium permeation barrier

A Mechanism for the Growth of a Plasma Electrolytic Oxide Coating on Al

Experimental Investigation on Contact Angles of Molten Lead–Lithium on Silicon Carbide Surface

Investigation on sol–gel Al 2 O 3 and hybrid phosphate-alumina insulation coatings for FeSiAl soft magnetic composites

Preparation of AlN microspheres/UHMWPE composites for insulating thermal conductors

Study on Al 2 O 3 /Fe-Al gradient coating assisted prepared by ionic liquid for Lead-Bismuth eutectic corrosion resistance

ACOUSTIC PROPERTIES OF Pb-17Li ALLOY FOR ULTRASONIC DOPPLER VELOCIMETRY

Preparation of Aluminide Coatings on the Inner Surface of Tubes by Heat Treatment of Al Coatings Electrodeposited from an Ionic Liquid

The Corrosion Behavior of Al/Al2O3 Composite Films with Ultra-Dense Structure Exposed to Lead-Bismuth Eutectic at 450 to 650 °C

Alumina Composite Coatings with Enhanced High-Temperature Electrical Insulating Properties on Ni-based Superalloy Substrates

High concentration of organic solvents in aluminum MAO: A study of structural and tribological property

Preparation of High Infrared Emissivity and Electrical Conductivity Coating on Magnesium Alloy