Abstract:The effect of long-term isothermal aging of Haynes 230 super-alloy in an advanced ultra-supercritical (A-USC) power plant at 700 degrees C for up to 10,000 h on microstructural evolution and tensile behavior. And utilizing a combination of the scanning electron microscope (SEM), X-ray diffraction analysis (XRD), and transmission electron microscope (TEM). Although the grain size and grain boundary M23C6 carbides did not change significantly, the dissolution of intercrystallite primary M6C carbides and the precipitation of intracrystalline secondary lamellar M6C carbides were observed at 2000 h to 10,000 h. According to the SEM and TEM results, it is shown that the dissolution of primary M6C carbides makes the W, Mo, and Cr in the gamma matrix increase, while the precipitation process of secondary M6C carbides is M+ 6 C -> M6C. To reduce the interfacial energy of the gamma matrix, secondary M6C carbides are precipitated in the crystal under long-term aging at 700 degrees C, with a gradual increase in time content. the best tensile and yield strengths at 750 degrees C occur after 4000 h of aging, with microscopic voids forming mainly around the granular M6C carbides in the crystal, but the solid solution strengthening effect of the matrix provides the strength. The worst strength and elongation occur after 10000 h aging, when the dissolution of granular M6C and secondary pre-cipitation of M6C carbides are most abundant, interfacial cavity formation of granular M6C carbides and brittle fracture of M6C carbide particles, and the growth of non-co-grained secondary M6C carbides with the matrix allow more microscopic cavities to appear during high-temperature tension, reducing the strength of Haynes 230 and plasticity.(c) 2023 Elsevier B.V. All rights reserved.

Corrosion Behavior of HAYNES 120 in High Temperature Simulated Ash Environment

Corrosion Behavior of Heat-Resistant Materials in High-Temperature Carbon Dioxide Environment

Characterization of Oxide Scales on Super-Alloy HR120 at 1000 °C in Air and Steam Environments

High Temperature Oxidation of Fe–Ni-base Alloy HR120 and Ni-base Alloy HAYNES 282 in Steam

High-temperature Corrosion of an Fe–Ni-based Alloy HR6W under Various Conditions at 750 °C and 810 °C: Effect of the Temperature, Water Vapor, Simulated Ash and SO2

Fireside Corrosion Behaviors Of Super304h And Hr3c In Coal Ash/Gas Environment With Different So2 Contents At 650 Degrees C

Experment of the corrosion behavior of Super304H steel in simulative coal ash/flue gas environment at 650 ℃

Fireside Corrosion Behaviors of Super304H and HR3C in Coal Ash/Gas Environment with Different SO 2 Contents at 650 °C

High-temperature corrosion of Fe-Ni-based alloy HR6W, Ni-based alloys Haynes 282 and Inconel 740 in supercritical water at 450 °C and 25 MPa

Studies on High Temperature Corrosion of Austenitic Heat‐Resistant Steels Super 304H/10Cr18Ni9Cu3NbN in Simulated and Real Combustion Gas Atmospheres

High Temperature Oxidation of Superalloys in Steam Environment

Oxidation Kinetics Of Haynes 230 Alloy In Air At Temperatures Between 650 And 850 Degrees C

Effect of Heat Treatment on Corrosion Behavior of a Newly Developed N-i Fe Based Superalloy in Simulated Coal Ash/Gas Environment

Corrosion Behavior of FeCrMnxAlCu High-Entropy Alloys in NaOH Solutions

Corrosion Performance of Heat-Resisting Steels and Alloys in Supercritical Carbon Dioxide at 650 °C and 15 MPa

High Temperature Oxidation and Corrosion Properties of High Entropy Superalloys

Effect of Heat Treatment on the Microstructure and Corrosion Resistance of Al0.75CoCr1.25FeNi High-Entropy Alloys

Corrosion of Alloy Haynes 230 in High Temperature Supercritical Carbon Dioxide with Oxygen Impurity Additions

Effect of Microstructural Evolution and Mechanical Properties of Haynes 230 Superalloy During Long-Term Aging at 700 °C

Corrosion of an Austenitic Heat-Resistant Steel HR3C in High-Temperature Steam and Supercritical Water

Corrosion Behavior of FeCoNiCrAl High-Entropy Alloy in Molten NaNO3-KNO3