Abstract:Low costly ferritic stainless steels, especially the Cr2O3-forming alloys, are promising interconnect materials for solid oxide fuel cells (SOFCs) due to their thermal expansion compatibility with other cell components. However, the oxidation resistance of commercial ferritic stainless steels in the operating temperature range of 600-800 degrees C is not adequate, forming relatively thick, poorly conducting oxide scale on the surface of the stainless steel interconnect and decreasing the cell performance. Surface modification is necessary to improve the oxidation behavior and electrical property. The present study investigates the effect of a LaCoO3 protective coating by the sol-gel process on the intermediate temperature oxidation behavior of SUS 430 alloy, which is frequently considered as the interconnect material for SOFCs. X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) were used to characterize the phase structure, surface morphology and composition of the coating and the oxide scale. The "4-probe" method was employed to determine the area specific resistance (ASR) of the surface oxides. Long-term thermally cyclic oxidation at 750 degrees C in air has shown that the oxidation kinetics obeys the parabolic rule with a rate constant of K=4.18x10(-15) g(2)/(cm(4).s), which is 1-2 orders of magnitude lower than that of the uncoated alloy, the LaCoO3 protective coating effectively suppresses the formation of Cr2O3 and slows down the growth of MnCr2O4 spinel. As a result, the oxidation resistance and electrical conductivity of the coated SUS 430 alloy are significantly enhanced, resulting in an ASR at 750 degrees C of only 3.13 m Omega.cm(2) after oxidation at 750 degrees C for 850 h in air and an extrapolated ASR of 21.5 m Omega.cm(2) for 4 x 10(4) h oxidation.

The Investigation of In-Situ Protection Effect of LaCo0.6Ni0.4O3-δ Cathode Contact Layer on High Temperature Oxidation of Fe-16Cr Alloy As Solid Oxide Fuel Cell Interconnect

Chemical compatibility and electrical contact between Ni–Cr–Mo alloy and LaCo0.6Ni0.4O3−δ in intermediate temperature solid oxide fuel cells

The Investigation of Ag & LaCo0.6Ni0.4O3−δ Composites As Cathode Contact Material for Intermediate Temperature Solid Oxide Fuel Cells

High Performance LaCo0.6Ni0.4O3-δ Cathode Contact Material for Intermediate Temperature Solid Oxide Fuel Cells

Stability Study on a Novel Micro Structure Configuration of Cathode Contact Layer for Solid Oxide Fuel Cell Stack

Promoted Cr-Poisoning Resistance of La2NiO4+ Δ-Coated PrBa0.5Sr0.5Co1.5Fe0.5O5+ Δ Cathode for Intermediate Temperature Solid Oxide Fuel Cells

LaCo0.6Ni0.4O3-δ as cathode contact material for intermediate temperature solid oxide fuel cells

High Performance LaCo<sub>0.6</sub>Ni<sub>0.4</sub>O<sub>3-</sub><sub>δ</sub> Cathode Contact Material for Intermediate Temperature Solid Oxide Fuel Cells

LaNi0.6Fe0.4O3 Cathode Contact Material: Electrical Conducting Property Manipulation and Its Effect on SOFC Electrochemical Performance

Evaluation of Protective La0.67Sr0.33MnO3–δ Coatings on Various Stainless Steels Used for Solid Oxide Fuel Cell Interconnects

The Investigation of Interaction Between La0.9Sr0.1MnO3 Cathode and Metallic Interconnect for Solid Oxide Fuel Cell at Reduced Temperature

Experimental Investigation of the Initial Stage of the Oxidation Mechanism of Co Coating for Solid Oxide Fuel Cell Interconnects at 650 °C

Evaluation of Lanthanum Ferrite Coated Interconnect for Intermediate Temperature Solid Oxide Fuel Cells

Characterization of La0.8Sr0.2Co0.5Mn0.5O3-δ Coating on Alloy Interconnect in SOFC

Effect of Lacoo3 Coating on the Intermediate Temperature Oxidation Behavior of Sus 430 Metallic Interconnect

Electrical and Electrochemical Performances Evaluation of LaNi<sub>0.6</sub>Fe<sub>0.4</sub>O<sub>3</sub> Cathode Contact and Current Collecting Layer in SOFCs

Oxidation and electrical behavior of Ni-Mn3O4-La2O3-coated SOFC interconnect steel

Characterization of the conductive protection layers on alloy interconnect for SOFC

Comparison of iron and copper doped manganese cobalt spinel oxides as protective coatings for solid oxide fuel cell interconnects

Fe doped Ni–Co alloy by electroplating as protective coating for solid oxide fuel cell interconnect application

Fabrication of Co 3 O 4 and La 0.6 Sr 0.4 CoO 3−δ –Ce 0.8 Gd 0.2 O 2−δ dual layer coatings on SUS430 steel by in-situ phase formation for solid oxide fuel cell interconnects