Abstract:The focus of this report was to understand the tensile properties and dynamic mechanical properties of bamboo powder (BP) reinforced polylactic acid (PLA) composite filaments which were treated with nano calcium carbonate (CaCO3), cellulose nanofibers (CNF), and micro-crystalline cellulose (MCC) using impregnation modification technology. The storage modulus (E’) of nano CaCO3-BP/PLA, MCC-BP/PLA, and CNF-BP/PLA composite filaments increased compared with BP/PLA composite filaments before the glass transition temperature Tg. When the temperature was above Tg, the reinforcement effect of nano CaCO3, MCC, and CNF gradually became less apparent. The loss modulus (E’’) and loss factor (tan δmax) of the nano CaCO3-BP/PLA, MCC-BP/PLA, and CNF-BP/PLA composite filaments was higher than that of BP/PLA composite filaments produced by the “one-step” method. The tensile strength (TS) results showed a similar trend. Compared with the control samples, the TS of nano CaCO3-BP/PLA, MCC-BP/PLA, and CNF-BP/PLA composite filaments produced by the “one-step” method (and the “two-step” method) increased by 40.33% (and 10.10%), 32.35% (and −8.61%), and 12.32% (and −12.85%), respectively. The TS of nano CaCO3-BP/PLA, MCC-BP/PLA, and CNF-BP/PLA composite filaments produced by the “one-step” method was slightly higher than those produced by the “two-step” method. The elongation at break (EAB) of BP/PLA composite filaments was higher than that of BP/PLA samples treated with nano CaCO3, MCC, or CNF. The PLA and modified BP were readily accessible through a simple mixing process. The rheological investigation of such mixtures showed that nano CaCO3, CNF, and MCC have different effects on the processability and rheological properties of composites.

Pyrolysis Kinetics and Mechanical Properties of Poly(lactic Acid)/bamboo Particle Biocomposites: Effect of Particle Size Distribution

Enhancement on the properties of polypropylene using bamboo particles: Effect of particle sizes and loadings

Poly(Lactic Acid) Biocomposites Reinforced With Ultrafine Bamboo-Char: Morphology, Mechanical, Thermal, And Water Absorption Properties

Effect of Low‐concentration Alkali Solution Pretreatment on the Properties of Bamboo Particles Reinforced Poly(lactic Acid) Composites

Preparation and Characterization of Maleic Anhydride Compatibilized Poly(lactic acid)/Bamboo Particles Biocomposites

Polypropylene biocomposites reinforced with bamboo particles and ultrafine bamboo-char: The effect of blending ratio

Nonisothermal Crystallization Behavior of Biocomposites from Poly(lactic Acid) and Bamboo Fiber

Effects of Bamboo Cellulose Nanowhisker Content on the Morphology, Crystallization, Mechanical, and Thermal Properties of PLA Matrix Biocomposites

Toughness Enhancement of Poly(lactic Acid), Bamboo Particle and Ultrafine Bamboo-Char Ternary Biocomposites by Polyethylene Glycol Plasticization

Composites of Polypropylene Reinforced with Ultrafine Bamboo-char: Morphology, Mechanical and Thermal Properties

Influence of Hot Press Molding Parameters on the Tensile Strength of Bamboo Fiber/PLA Composites

Kinetics of Bamboo Pyrolysis

Study on Properties of Modified Bamboo Fiber Reinforced Polypropylene Composites

Reinforcement of Polylactic Acid for Fused Deposition Modeling Process with Nano Particles Treated Bamboo Powder

Poly(l-lactide)/poly(d-lactide)/bamboo fiber (BF) bio-composites with enhanced heat resistance, mechanical and rheological performance

Effect of different amounts of bamboo charcoal on properties of biodegradable bamboo charcoal/polylactic acid composites

Development of Biodegradable Flame-Retardant Bamboo Charcoal Composites, Part I: Thermal and Elemental Analyses.

Characterizations of poly-lactic acid/polypropylene filled with bamboo charcoal powder

Co-pyrolysis of bamboo sawdust and plastic: Synergistic effects and kinetics

Interfacial interaction improvement of polylactic acid/bamboo-char biocomposites for high toughness, good strength, and excellent thermal stability

Development of polylactic acid‐untreated bamboo filler composite and its chemical and mechanical properties