Abstract:Wire and arc additive manufacturing (WAAM) has emerged as a highly promising technique for manufacturing large-scale steel structural elements. However, the distinct mechanical properties of WAAM steel could potentially lead to different performance of WAAM steel bolted connections compared to the traditional steel bolted connections. This study aims to investigate the material properties of WAAM steel and the structural behaviours of WAAM steel bolted connections, focusing on the effects of print layer orientation and connection plate geometrical dimensions. A total number of 24 WAAM steel coupon specimens with three different print layer orientations and 36 WAAM double-shear bolted connections with two print layer orientations and different geometric dimensions were designed, fabricated and tested under monotonic tension. These specimens were measured using a 3D laser scanner and Digital Image Correlation (DIC) was adopted to measure the structural response during testing. The impact of print layer orientations on WAAM material properties and the effects of WAAM material properties on bolted connections were analysed and discussed. The current design codes for traditional steel bolted connections were evaluated against the test results of WAAM steel bolted connections. The study found that the print layer orientations of WAAM steel plates initiated an anisotropic material property of the coupon specimens, demonstrated by the differences in ultimate tensile strength and strain of specimens with different print layer orientations. Five failure modes, including net section tension, shear-out, bearing, end-splitting, and block shear failure were observed for the bolted connections. The material anisotropy further affects the performance of the bolted connections, though in the same dimensions, 28% of the specimens presented different failure modes due to the different print layer orientations. The effectiveness of current steel design standards was compromised by inaccurate predictions of failure modes due to the distinct end-splitting failure mode and the effects of material anisotropy, though the predictions of the ultimate capacities of the WAAM lap shear specimens were relatively accurate.

A study of the load-deflection rate of multiloop edgewise arch(MEAW) and the superelastic nickel-titanium wire

Experimental Study and Residual Performance Evaluation of Corroded High-Tensile Steel Wires

A theoretical analysis on mechanical character of multiloop edgewise arch wire

Experimental Study on Wire and Arc Additively Manufactured Steel Double-Shear Bolted Connections

Multi-scale Deformation Behavior Investigation of 18cr–8ni Austenitic Steel Subjected to Low-Cycle Fatigue Loading

Tensile Deformation Behaviors of CuNi Alloy Processed by Equal Channel Angular Pressing

Test and Analysis of the Interfacial Bond Behaviour of Circular Concrete-Filled Wire-Arc Additively Manufactured Steel Tubes

Effect of Multilayer Structure and Column Array Structure on Mechanical Properties and Fracture Behavior of Heterogeneous Steel

An Experimental Study of the Superelastic Behavior in NiTi Shape Memory Alloys under Biaxial Proportional and Non-Proportional Cyclic Loadings

Load-deflection characteristics of superelastic and thermal nickel-titanium wires

Microstructure Evolution and Mechanical Properties of a Wire-Arc Additive Manufactured Austenitic Stainless Steel: Effect of Processing Parameter

Load-deflection and surface properties of coated and conventional superelastic orthodontic archwires in conventional and metal-insert ceramic brackets

Ratcheting and fatigue properties of the high-nitrogen steel X13CrMnMoN18-14-3 under cyclic loading

Comparison in Deformation Behavior, Microstructure, and Failure Mechanism of Nickel Base Alloy 625 under Two Strain Rates

Multiaxial Low Cycle Fatigue Behavior and Life Prediction of Wire Arc Additive Manufactured 308L Stainless Steel

Effects of structural geometry on the localized deformation of superelastic NiTi sheets

Experimental Research of Replaceable Q345GJ Steel Shear Links Considering Cyclic Buckling and Plastic Overstrength

Investigation of extremely low cycle fatigue behavior of low yield strength steel LY225 under different stress states

Strengthening of CoNiFeV0.5Mo0.2 Medium Entropy Alloy Wire Rods with Loading-Unloading Cycles

Effect of Cyclic Loading on Apparent Young's Modulus and Critical Stress in Nano-Subgrained Superelastic NiTi Shape Memory Alloys

Deflection load characteristics of laser-welded orthodontic wires