Review of Recent Researches on PD Monitoring in Gas Insulated Equipment in Japan

刘卫东,金立军,黄家旗,钱家骊

DOI: https://doi.org/10.13336/j.1003-6520.hve.2001.02.033

2001-01-01

Abstract:This paper relates recent researches on partial discharge on line monitoring technique in gas insulated equipment in Japan.These research works include sensors,signal propagation characteristics,signal processing and fault diagnosis as well.

What problem does this paper attempt to address?

Partial discharge diagnosis by simultaneous observation of discharge pulses and vibration signal

Baowen Liu,Hongzhong Ma,Ping Ju

DOI: https://doi.org/10.1109/TDEI.2016.006072

IF: 2.509

2017-01-01

IEEE Transactions on Dielectrics and Electrical Insulation

Abstract:Protrusion defects on inner conductor can seriously weaken the dielectric strength of gas insulated switchgear (GIS). In practice, pulse current method (IEC 60270) and vibration method sometimes are ineffective for this type of defect. Clarification of coincidence of partial discharge (PD) characteristics measured with both methods is very important for further application of the vibration method....
Examination and Research on the Partial Discharge Fault Diagnostics in Gas Insulated Switchgear

Lijun Jin,Mingrui Zhang,Weidong Liu

DOI: https://doi.org/10.3321/j.issn:1000-6753.2005.11.019

2005-01-01

Abstract:A detecting system of PD for model GIS has been set up. Investigation was made on the diagnosis of the PD in GIS. The measurement included the Ultra High Frequency (UHF) detection, conventional PD measurement and the power phase analysis. The sort of PD is classified by the PD characteristic research. Then Discharge level of UHF signal is estimated based on its sort and the conventional PD measurement. The practicality of UHF detection is development in the engineering.
On-line Partial Discharge Monitoring and Diagnostic System

Wensheng Gao,Zhang Ling-ju

2006-01-01

Abstract:This paper developed an on-line partial discharge(PD) monitoring and diagnostic system.Partial discharge(PD) is an important factor for judging the insulation condition of power equipments.On-line monitoring system can inspect power equipments' traits continuously and predict the latent faults in time by observing the change of traits.Now the system has been successful appliedin some substations,and the application results are satisfied.
Review on Detection and Analysis of Partial Discharge along Power Cables

Xiaohua Zhang,Bo Pang,Yaxin Liu,Shaoyu Liu,Peng Xu,Yan Li,Yifan Liu,Leijie Qi,Qing Xie

DOI: https://doi.org/10.3390/en14227692

IF: 3.2

2021-11-17

Energies

Abstract:Partial discharge (PD) detection and analysis plays a crucial role for acceptance testing and condition monitoring of power cables. Various aspects are related to PD in power cables from theory to practice. This paper first summarizes the PD mechanism and models used for PD analysis in power cables. Afterwards, PD detection is addressed in the aspects of off-line test, on-line test, and sensors. PD analysis is discussed in detail. Specifically, related quantities and algorithms for PD analysis are outlined. PD characteristics with affecting factors, e.g., dielectric type, load, and applied voltage are discussed. Experience on PD development trend with measurements in field is analyzed. Based on the comprehensive review, challenges of PD detection and analysis along a power cable are proposed.

energy & fuels
On Site Detection and Localization of Partial Discharge in Hydropower Plant GIL/GIS Based on Ultra-high Frequency Technique

Lihua Li,Yang Liu,Feng Chen,Xinzhi Yang,Xing Li,Mingtao Yu

DOI: https://doi.org/10.1109/icopesa61191.2024.10743434

2024-01-01

Abstract:Partial discharge (PD) detection is an important method for diagnosis and assessment of insulation defects in gas- insulated switchgears (GISs) and gas-insulated transmission lines (GILs). The ultra-high frequency (UHF) method is widely used for on-site PD detection of GIL/GIS owing its good sensitivity and anti-interference performance. In this paper, PD detection and localization diagnosis of GIL/GIS equipment in a hydropower plant is conducted. PD signal is detected in the GIL/GIS B-phase at the outgoing line yard using the UHF technique. Then, based on localization analysis, it is finally determined that the PD source is located on the insulator between the disconnector and current transformer. According to the PD diagnosis, the insulator is replaced and the X-CT flaw detection result shows that there are two 1–2 mm gaps inside this insulator. Subsequently, the PD test in the factory shows that significant and stable PDs are provoked by the dismantled insulator. These fully confirm the accuracy of on-site PD detection and localization diagnosis. The research of this paper provides good guidance for on-site equipment maintenance and helps to improve equipment stability.
Diagnosis of Partial Discharge in GIS Based on UHF Sensing Technique

Jin, L.J.,Huang, J.Q.,Liu, W.D.,Qian, J.L.

DOI: https://doi.org/10.1109/iseim.2001.973636

2001-01-01

Abstract:A gas-insulated substation (GIS) test model was set up and a GIS partial discharge (PD) online detection system by a UHF sensing technique was developed. Investigation was made on the diagnosis of PDs in GIS. Testing with different insulation defects in GIS and comparing between the waveforms of the UHF measurement, the features of the different PDs were investigated, and the PD form recognition was performed. Based on the results of the UHF PD measurement and the conventional PD measurement, the PD quantities of the defects in GIS were estimated
Investigation of Frequency Characteristics of Typical PD and the Propagation Properties in GIS

Wensheng Gao,Dongbo Zhao,Dengwei Ding,Senjing Yao,Yuming Zhao,Weidong Liu

DOI: https://doi.org/10.1109/tdei.2015.7116362

IF: 2.509

2015-01-01

IEEE Transactions on Dielectrics and Electrical Insulation

Abstract:The secure operation of Gas Insulated Switchgear (GIS) is crucial for the bulk power systems, since the failure of GIS apparatus would cause severe interruption of power transforming and power supply at substations. Therefore, the monitoring and maintenance schemes of GIS devices have gradually taken the reliability-based indices into account, of which Partial Discharge (PD) levels in online monitoring are of substantial significance because PD serves as a major cause of insulation break-down. Ultra High Frequency (UHF) method is becoming widely adopted as the major inspection approach for PD in GIS. This paper presents the experiment-based results of the frequency characteristics of UHF signals caused by PD in typical defects using entire GIS operating system platforms. Specifically, the results covered the propagation attenuation of the UHF signals with peak to peak value and cumulative energy through typical structures, including basin-type insulators, L-shaped branch, isolating switches, current transformers, etc. The results serve as substantial criteria for optimal band width selection for high frequency detection, and as notable concerns to improve the sensitivity of UHF detection and the efficiency of online monitoring by effectively locating the external sensors for PD UHF detection.
Review of research on partial discharge detection techniques of high voltage switchgear

Zheng Chao,Zheng Yongkang,Zhong Jun,Wang Yongfu,Zhao Zhang Haiyang,Ren Bo

DOI: https://doi.org/10.1088/1742-6596/1550/3/032084

2020-05-01

Journal of Physics: Conference Series

Abstract:Abstract Partial discharge inside a high-voltage switchgear can cause serious accidents. Partial discharge detection can reduce the incidence of accidents. This article summarizes the current research status of common high-voltage switchgear partial discharge detection technologies (Transient Earth Voltage or TEV, Utrasonic or AE and Ultra-High Frequency or UHF), introduces the research status of partial discharge model identification and localization of PD source, and finally looks forward to future research directions.
Investigation of the Evaluation of the Pd Severity and Verification of the Sensitivity of Partial-Discharge Detection Using the Uhf Method in Gis

Wensheng Gao,Dengwei Ding,Weidong Liu,Xinhong Huang

DOI: https://doi.org/10.1109/tpwrd.2013.2242206

IF: 4.825

2014-01-01

IEEE Transactions on Power Delivery

Abstract:The measurement of partial discharge (PD) using ultra-high frequency (UHF) method is considered an effective approach to monitor the online condition of the equipment, which is used to facilitate the detection of incipient defects in gas-insulated switchgear (GIS). In this paper, in order to assess the severity of PD defects using UHF method, the actual 220-kV GIS were subjected to experimentation. The PD was measured simultaneously by using the UHF method and the IEC60270 measurement technique. The combined measurement has been carried out on different defects in PD test cells, including the floating metal, metallic protrusion, and void in epoxy resin. The inner coupler installed in the GIS tank, and the outer coupler placed outside the spacer, are used to measure the UHF signal. The relationship of the apparent charge and the amplitude of the time-domain signal, and the integral energy from 300 MHz to 1.6 GHz of the signal induced by PD in GIS are analyzed thoroughly. In this way, the severity of PD can be quantified using the UHF signal. In addition, to verify the sensitivity of the UHF detection method, a pulse generator with a rise time of about 500 ps is designed. The GIGRE method for the verification of sensitivity, which is used worldwide, is applied in the experiment. The results of the pulse generator experiment are compared to the results produced by the actual discharge sources, and several possible approaches of improving this method are proposed.
Investigation of disc-type sensors using the UHF method to detect partial discharge in GIS

yang xu,weidong liu,wensheng gao

DOI: https://doi.org/10.1109/TDEI.2015.005132

IF: 2.509

2015-01-01

IEEE Transactions on Dielectrics and Electrical Insulation

Abstract:The disc-type UHF sensor is considered among the simplest couplers for partial discharge (PD) detection in gas-insulated switchgear (GIS). This paper mainly focuses on the improvement of the sensitivity of the disc-type sensor. Disc-type sensors with different dimensions were tested on a 220 kV model GIS to find the critical parameters that determine the sensitivity of the sensor. The waveform of ...
Detection and Identification Technologies of Wide Band Partial Discharge

RUAN Ling,ZHENG Zhong,GAO Sheng-you,GUI Jun-feng,SHEN Yu,XIE Qi-jia

2010-01-01

Abstract:A wide-band online partial discharge(PD)detection method is discussed to minimize the influence of the noise and interferences during the course of measurement and diagnosis followed.The traditional IEC pulse current detection method and the recently developed ultra high frequency detection method have limited their bandwidth to avoid the abundant ambient noise and interference,and loss of the information of the PD signals as well.The methods can not record the entire discharge waveforms of the PD current pulses,causing a fundamental lack of information to neither differentiate various signals and noises,nor distinguish various PD or interference patterns.The wide band detection method covers a bandwidth wide enough to record the entire partial discharge pulse waveforms.Based on the features of their pulse waveforms,such signals can be separated and recognized in a'clean'condition.An experiment employing such method on a 110kV cable with several discharge patterns and onsite noises is presented.The analysis shows that,with sufficient information of the entire waveform,those discharge patterns can be separated,and each of the'clean and pure'sub-patterns,such as the internal discharge and background noises can be isolated and well recognized.For field PD detection and diagnosis,the method would increase the ability to remove the impact of onsite noises and interferences,as well as the ability to diagnose the insulation condition based on the PD information.
The Characteristics and Detection of the Partial Discharge Induced by the Micro Cracks in GIS Insulators

Xiao Li,Yang Xu,Jiangrong Cheng,Weidong Liu,Wensheng Gao

DOI: https://doi.org/10.1109/CMD.2018.8535818

2018-01-01

Abstract:The micro cracks resulted from the defective manufacturing technology are common to see in GIS insulators, and many researches have already been done on it. However, most of these studies are based on the simulative defects made in laboratories, rather than on the defects on real made insulators, and thus the equivalence between the experimental condition and the practical situation in real substations cannot been guaranteed. In this paper, partial discharge (PD) experiments are carried out on a real made GIS post insulator with micro crack inside. It is found that the ultra-high frequency (UHF) method is not sensitive to the PD of this type based on the investigation on the PD characteristics, and the mechanism of the PD process is analyzed to explain why it cannot be detected by the UHF method. According to the special PD characteristics the defect displayed, suggestions on the adjustment of the PD frequency band is made in order to find the micro cracks in GIS insulators on-site.
Development and Application of DC Partial Discharge Test System

NIE Dexin,SHA Yanchao,ZHOU Yuanxiang,WU Zhirong,DENG Jiangang

DOI: https://doi.org/10.3969/j.issn.1003-6520.2013.08.025

2013-01-01

Abstract:Direct current (DC) partial discharge (PD) test has drawn extensive attention from world-wide electric power research institutes in recent years. However, presently, no DC PD detection device on the market has the statistical function. Thus, we developed a test system for PD detection under DC voltage, which is characterized by strong anti-jamming capability, continuous high-speed real-time data acquisi- tion and effective, complete detection of DC PD signals. The DC PD mechanism, as well as the measuring principles, software system, and hardware design of the test equipment were introduced. Adopting typical electrode pairs, we tested the statistical spectrum of PD under DC voltage. The main difference in statistical spectrums between parallel plate electrodes and needle-plate electrodes was that the time interval between two consecutive discharges for needle-plate electrodes has obviously larger variation range than that for parallel plate electrodes, which could be the convincing proof for distinguishing the type of electrodes under DC PD. Practical results indicate that the proposed sys- tem can measure time domain signals of DC PD of oil-paper insulation effectively and promptly, and it can be used to determine and detect defects in DC power transmission equipment.
RESEARCH AND DEVELOPMENT OF ON-LINE MONITORING SYSTEM WITH PARTIAL DISCHARGE IN XLPE POWER CABLES

赵中原,吕征宇,段乃欣,邱毓昌

DOI: https://doi.org/10.3321/j.issn:1000-1026.2004.05.013

2004-01-01

Abstract:Monitoring partial discharge (PD) is an important means to assess the electrical insulation condition of XLPE power cables. In China, the frequency of the method used in PD detection of the XLPE power cables is low. Hence an electromagnetic coupling method with wide frequency bandwidth is presented. The electromagnetic coupling system consists of Rogowski coil, amplifier, filter and digital oscillograph. Detection of several simulated defects and XLPE cables with artificial defects shows that this method provides high sensitivity compared with the IEC 60270 method. This detection system can detect PD signal and recognize different defects.
Review of Partial Discharge Activity Considering Very-Low Frequency and Damped Applied Voltage

Mohamad Ghaffarian Niasar,Xiaolei Wang,Respicius Clemence Kiiza

DOI: https://doi.org/10.3390/en14020440

IF: 3.2

2021-01-15

Energies

Abstract:When detecting the presence of partial discharge (PD) activity in the insulation system in high-voltage equipment, the excitation voltages at variable frequency have been widely used instead of power-frequency (50/60 Hz) sinusoidal voltage in order to reduce the charging power. This work reviews the relevant research on PD activity at very low frequency (VLF) method, including sinusoidal or cosine-rectangular voltage shape, and damped AC (DAC) method. Based on the research history and development status, some major PD characteristics, such as PD inception voltage (PDIV), PD amplitude, PD charge, PD phase-resolved pattern, and several hot issues, such as surface charge decay and statistical time lag, have been discussed. Moreover, the advantages, disadvantages, and applied conditions of two reviewed methods has been summarized. Finally, the prospects have been made on the main development trends of this research field in the future.

energy & fuels
Partial Discharge Characteristics of a Void Defect inside an Actual 252-kV GIS Post Insulator

Yiping Ji,Shaojing Wang,Min Ding,Xianqin Deng,Xing Li,Yanqing Lu

DOI: https://doi.org/10.1109/ICEMPE57831.2023.10139467

2023-01-01

Abstract:Epoxy insulation is one of the important components in gas insulated switchgears (GISs), and its reliability directly affects the safety and stability of the GIS equipment. Epoxy insulation void is a typical defect in GIS insulator, which will cause partial discharges (PDs), accelerate insulation deterioration, and finally lead to insulation breakdown. In this paper, a high-sensitive experimental platform for 252-kV GIS post insulator PD test is established, and the PD characteristics of an abnormal insulator under different voltages are investigated. The experiment result shows that under the routine PD test voltage, the PDs of this insulator is lower than 1 pC. The discharge is weak and sporadic, and traditional PD methods may fail to detect this defect. Under a higher test voltage, PD is enhanced, which is conducive to defect detection. Then the X-flaw detection is performed and the result shows that there is a small void defect inside the insulator with PDs, which confirms that the PDs are generated by internal defects. Finally, the discharge characteristics and mechanism of the void defect are analyzed and discussed. The results in this paper provide an important reference for further mastering the PD characteristics of void defects inside GIS insulators and is helpful for defect detection in routine PD test.
Partial Discharge Detection and Characteristics of Gas-insulated Substation Free Metal Particles Based on Acoustic Emission

Runjie Shen,Yanghui Ou,Ying Zhou,Weishi Zhao,Xuefeng Li

DOI: https://doi.org/10.18494/sam.2019.2267

IF: 1.2

2019-01-01

Sensors and Materials

Abstract:Metal particles can easily be produced in the production and installation of a gas-insulated substation (GIS). The partial discharge (PD) induced by metal particles is a significant security risk to GIS. At present, some related research studies focus on the PD of individual metal particles, but less attention is paid to that of accumulated metal particles. In this study, the PD of the accumulated metal particles was investigated. A defect model of surface free metal particles on a basin-type insulator was set up. Four models of free metal particles of different sizes lying inside the GIS were designed. PD signal waveforms were measured using acoustic emission (AE) sensors. The frequency spectrum characteristics of the PD signal were analyzed, and the PD characteristics under different voltage waveforms were compared. Research results showed that, through the detection of PD signals, the accumulation of free metal particles on the surface of the insulator could be predicted and evaluated to ensure the safe operation of GIS equipment.
Passive Wireless Partial Discharge Sensors with Multiple Resonances

Zhenheng Xu,Bing Tian,Shiqi Guo,Qingan Huang,Lifeng Wang,Lei Dong

DOI: https://doi.org/10.3390/mi15050656

IF: 3.4

2024-05-18

Micromachines

Abstract:Partial discharge (PD) is the dominant insulating defect in Gas-Insulated Switchgear (GIS). The existing detection methods are mainly divided into built-in wire-connected disk antennas with destructive drilling and external ultra-high frequency antennas with poor anti-interference ability. This research introduces a passive wireless PD sensor implanted inside GIS on the observation window. The sensor is implemented by a sheeting branch-inductor with multiple resonances which is able to enhance detection sensitivity. A coaxially aligned readout circuit, positioned outside the GIS, interrogates the PD sensor to wirelessly obtain the PD signal. The proposed sensing scheme improves signal-to-noise ratio and ensures minimal disruption to the electric field distribution inside GIS. An experimental setup was established in a controlled laboratory environment to benchmark the multi-resonant sensor against the commercial UHF sensor. A 2.5-times enhancement of signal strength was observed. Since our sensor was implanted inside the GIS, a high signal-to-noise ratio (68.82 dB) was obtained. Moreover, we constructed a wireless calibration test to investigate the accuracy of the proposed sensor. The precision of the signal test was as high as 0.72 pC. The pulse phase distribution information was collected to demonstrate a phase-resolved partial discharge (PRPD) pattern. The experiment results validate the effectiveness of the proposed method and demonstrate excellent performance in PD detection.

nanoscience & nanotechnology,instruments & instrumentation,physics, applied,chemistry, analytical
Analysis Of The Intrinsic Characteristics Of The Partial Discharge Induced By Typical Defects In Gis

Wensheng Gao,Dengwei Ding,Weidong Liu

DOI: https://doi.org/10.1109/tdei.2013.6518948

IF: 2.509

2013-01-01

IEEE Transactions on Dielectrics and Electrical Insulation

Abstract:Partial discharge (PD) monitoring plays an important role in the maintenance of the high voltage (HV) apparatus, such as transformer and gas-insulated substation (GIS). In recent years, the ultra high frequency (UHF) method for PD detection arouses great interest of many researchers because of its high sensitivity and anti-interference capability. The coupling of UHF signal and process of the signal constitute the UHF detection method. There are three key components for the coupling of UHF signal in GIS, including the frequency spectrum characteristics of the PD source, the propagation characteristics in GIS, the coupling style and the capability of the UHF coupler. Many researchers are interested in the recognition algorithm and the analysis procedure of the PD data. But the intrinsic attributes of the partial discharges should attract more attentions because they are the foundation of the UHF detection method. This paper focuses on the intrinsic characteristics of the typical defects in GIS, such as the amplitude of the time-domain signal and frequency spectrum characteristics. Four types of typical partial discharge sources are designed and fabricated, including floating metal, protrusions, particle on the spacer, and void in solid insulation. Several different structure sizes of each defect are applied to ensure the consistency of the results and discover the factors that affect the frequency spectrum characteristics. The results of the study present the essential characteristics of the partial discharge. It can be applied to the design of the coupler and amplifier circuit. In addition, the sensitivity and anti-interference capability of the UHF method are promoted effectively, and it is valuable for calibrating the intensity of PD in GIS.
Research on the Typical Partial Discharge Using the UHF Detection Method for GIS

Wensheng Gao,Dengwei Ding,Weidong Liu

DOI: https://doi.org/10.1109/tpwrd.2011.2166089

2011-01-01

Abstract:GIS plays an important role in power systems for its maintenance-free and less influence to environmental and industrial conditions.In order to monitor the on-line condition,ultra high frequency(UHF) method is widely used for defect diagnosis of GIS.Therefore,five types of typical partial discharge(PD) sources were designed and fabricated to imitate the defects in GIS online.To distinguish the types of partial discharges,some meaningful parameters behind the UHF signal were extracted and discussed.In general,the conventional phase-resolved partial discharge(PRPD) and pulse sequence analysis method is adopted to discriminate partial discharge,but sometimes it may be less convenient to employ because of the absence of the phase information.Consequently,nine comprehensive parameters realized by processing the UHF pulse magnitude sequence q and time interval sequence Δt are introduced.The parameters can describe exactly the physical characteristics of different partial discharges.By means of the parameters,the pattern classification of PD without employing the phase information of the applied voltage could be achieved.The clustering results by SPSS indicate that there is evident difference in the characteristic coefficients.

Review of Recent Researches on PD Monitoring in Gas Insulated Equipment in Japan

Partial discharge diagnosis by simultaneous observation of discharge pulses and vibration signal

Examination and Research on the Partial Discharge Fault Diagnostics in Gas Insulated Switchgear

On-line Partial Discharge Monitoring and Diagnostic System

Review on Detection and Analysis of Partial Discharge along Power Cables

On Site Detection and Localization of Partial Discharge in Hydropower Plant GIL/GIS Based on Ultra-high Frequency Technique

Diagnosis of Partial Discharge in GIS Based on UHF Sensing Technique

Investigation of Frequency Characteristics of Typical PD and the Propagation Properties in GIS

Review of research on partial discharge detection techniques of high voltage switchgear

Investigation of the Evaluation of the Pd Severity and Verification of the Sensitivity of Partial-Discharge Detection Using the Uhf Method in Gis

Investigation of disc-type sensors using the UHF method to detect partial discharge in GIS

Detection and Identification Technologies of Wide Band Partial Discharge

The Characteristics and Detection of the Partial Discharge Induced by the Micro Cracks in GIS Insulators

Development and Application of DC Partial Discharge Test System

RESEARCH AND DEVELOPMENT OF ON-LINE MONITORING SYSTEM WITH PARTIAL DISCHARGE IN XLPE POWER CABLES

Review of Partial Discharge Activity Considering Very-Low Frequency and Damped Applied Voltage

Partial Discharge Characteristics of a Void Defect inside an Actual 252-kV GIS Post Insulator

Partial Discharge Detection and Characteristics of Gas-insulated Substation Free Metal Particles Based on Acoustic Emission

Passive Wireless Partial Discharge Sensors with Multiple Resonances

Analysis Of The Intrinsic Characteristics Of The Partial Discharge Induced By Typical Defects In Gis

Research on the Typical Partial Discharge Using the UHF Detection Method for GIS