Abstract:Cu matrix composites have received increased attention in a wide industrial area because of their excellent mechanical properties and good electrical and thermal conductivity. However, the addition of general ceramic reinforcements often leads to a marked reduction in electrical conductivity for Cu matrix composites. In this study, the ZrB 2 -reinforced Cu composites have been developed to overcome this drawback since these metal borides possess relatively high electrical conductivity. The 5 wt.% ZrB 2 /Cu composites were prepared using hot-pressed sintering techniques at varying temperatures from 760 to 920°C. The influence of sintering temperature on the microstructure, relative density, and mechanical and electrical properties was examined. The results of the SEM observation show that ZrB 2 particles are seamlessly integrated into the Cu matrix for all ZrB 2 /Cu composites. The average grain size of the Cu matrix increases from 360 to 980 nm with the increase of the sintering temperature. The increase in sintering temperature also leads to the surface porosity decrease from 1.4 to 0.4%. The relative density and electric conductivity of the composites increase at the same time as the sintering temperature increases. However, microhardness increases and decreases, with a maximum value of 92 HV0.2 achieved at 840°C. The elastic modulus and nanohardness maps determined from the nanoindentation indicate that the reinforced ZrB 2 particles demonstrate the highest values for elastic modulus (340–500 GPa) and nanohardness (30–48 GPa). At the same time, the Cu matrix possesses a modulus of 100–200 GPa and nanohardness of about 10 GPa. TEM observation confirmed that the sintering temperature exhibits little influence on the interface reaction between ZrB 2 and Cu. Both sharp interface and interface with amorphous transition layer are observed. The variation of microhardness is mainly due to the strengthening of grain refinement and to the mismatch of the thermal expansion coefficients. The above results can provide further insights into the deeper understanding of the role of sintering temperature during hot-pressed sintering.

Transmission electron microscopy characterization of effect of graphite in zrb 2 – based composites

Effect of TiB_2 content on microstructure and mechanical properties of in-situ fabricated TiB_2/B_4C composites

Improvement in the thermal conductivities and bending strengths of graphite film/Cu composites by matrix alloying with Zr

Influence of graphite on the low-frequency fatigue behavior of zirconium diboride ceramics

High‐temperature tensile strength and fracture behavior of ZrB2‐SiC‐graphite composite

The effect of alloying element on the thermophysical properties of carbon fiber-graphite flakes/copper composites

Effects of Zr-Cu Alloy Powder on Microstructure and Properties of Cu Matrix Composite with Highly-Aligned Flake Graphite

A TEM study of nanostructures and interfaces in the hot-press sintered ZrB2–SiC–Si3N4 composites

Effect of Sintering Temperature on the Microstructure and Properties of High-Strength and Highly Conductive 5 wt.% ZrB2/Cu Composite

Mechanical Properties of Short Carbon Fiber Reinforced ZrB2–SiC Ceramic Matrix Composites

Effects of ZrC content on the microstructure and mechanical property of ZrC/ZTA composites consolidated by hot pressing

Effect of sintering temperature and holding time on the microstructure and mechanical properties of ZrB2–SiCw composites

Tribological Performance of In-Situ Epoxy Composites Filled with Micro-Sized ZrB 2 Particles

Microstructure, Mechanical, and Thermal Properties of in Situ-Synthesized (zrb2+sic)/zr2[al(si)]4c5 Composites

Beneficial effect of low BN additive on densification and mechanical properties of hot-pressed ZrB2–SiC composites

Microstructure And Mechanical Properties Of Zrb2-Based Composites With Laminated Structure

Effect of nano-graphite on mechanical properties and oxidation resistance of ZrB2–SiC–graphite electrode ceramics

Microstructure evolution and mechanical properties of in-situ ZrB2/Al7085 nanocomposites during hot rolling deformation

Effects of Zr element on the microstructure and mechanical properties of B4C/Al composites fabricated by melt stirring method

Fabrication and Properties of Short Carbon Fiber-ZrB2 Ceramic Matrix Composites

Effects of ZrB2 on Mechanical Properties of Al2O3-ZrB2-SiC Composite Ceramics at Room Temperature