Abstract:Carbon nanotube (CNT) is a promising electrode material and has been used as an anode modifier in microbial fuel cells (MFCs). In this study, a new method of simultaneously adding CNT powders and Geobacter sulfurreducens into the anode chamber of a MFC was used, aiming to form a composite biofilm on the anode. The performance of MFCs such as startup time and steady-state power generation was investigated under conditions of different CNT powders dosages. Results showed that both the startup time and the anodic resistance were reduced. The optimal dosage of CNT powders pre-treated by acid was 4mg/mL for the anode chamber with an effective volume of 25mL. The anodic resistance and output voltage of the MFC with CNT powders addition were maintained around 180Ω and 650mV during 40 days operation, while those of the MFC without CNT powders addition increased from 250Ω to 540Ω and decreased from 630mV to 540mV, respectively, demonstrating that adding CNT powders helped stabilize the anodic resistance, thus the internal resistance and power generation during long-term operation. Based on cyclic voltammogram, the electrochemical activity of anodic biofilm was enhanced by adding CNT powders, though no significant increase of the biomass in anodic biofilm was detected by phospholipids analysis. There was no remarkable change of ohmic resistance with an addition of CNT powders revealed by current interrupt method, which indicated that the rate of mass transfer might be promoted by the presence of CNT powders.

Addition of Conductive Particles to Improve the Performance of Activated Carbon Air-Cathodes in Microbial Fuel Cells

Sewage Sludge-Derived Carbon-Doped Manganese As Efficient Cathode Catalysts in Microbial Fuel Cells

Enhanced Activated Carbon Cathode Performance for Microbial Fuel Cell by Blending Carbon Black

Carbon Material Optimized Biocathode for Improving Microbial Fuel Cell Performance

Enhanced Electricity Generation and Water Pressure Tolerance Using Carbon Black-Based Sintered Filtration Air-Cathodes in Microbial Fuel Cells

Long‐Term Performance of Chemically and Physically Modified Activated Carbons in Air Cathodes of Microbial Fuel Cells

Nitrogenous mesoporous carbon coated with Co/Cu nanoparticles modified activated carbon as air cathode catalyst for microbial fuel cell

Facilely Prepared Carbon Dots as Effective Anode Modifier for Enhanced Performance of Microbial Fuel Cells

Enhanced Oxygen and Hydroxide Transport in a Cathode Interface by Efficient Antibacterial Property of a Silver Nanoparticle-Modified, Activated Carbon Cathode in Microbial Fuel Cells

Using ammonium bicarbonate as pore former in activated carbon catalyst layer to enhance performance of air cathode microbial fuel cell

Highly Efficient Improvement of Power Generation and Waste Removal in Microbial Fuel Cell by Associating Activated Carbon with a Novel Porous Iron-Nitrogen-doped Carbon Nanosphere

Immobilization of a Metal-Nitrogen-Carbon Catalyst on Activated Carbon with Enhanced Cathode Performance in Microbial Fuel Cells.

The effect of thermal-gas-chemical treatment of carbon black on electrocatalytic activity of electrodes in alkaline fuel cells

Power Generation Using an Activated Carbon and Metal Mesh Cathode in A Microbial Fuel Cell

Fe3C-modified porous carbon as anode electrocatalyst for improving extracellular electron transfer and removing Cr(VI) in microbial fuel cells

Performance Improvement in Direct Methanol Fuel Cell Cathode Using High Mesoporous Area Catalyst Support

Use of Pyrolyzed Iron Ethylenediaminetetraacetic Acid Modified Activated Carbon As Air-Cathode Catalyst in Microbial Fuel Cells.

Power Generation by Packed-Bed Air-Cathode Microbial Fuel Cells

Carbon nanotube powders as electrode modifier to enhance the activity of anodic biofilm in microbial fuel cells.

Microwave Preparation of Catalyst Layer for Enhancing the Oxygen Reduction of Air Cathode in Microbial Fuel Cells

Enhanced Electricity Generation for Microbial Fuel Cell by Using Electrochemical Oxidation to Modify Carbon Cloth Anode