Abstract:This paper presents a novel seismic isolation floor system that aims to address the issue of incongruent deformation between the floor and the resilient steel frame structure. The proposed study introduces a design methodology for the seismic isolation floor system, along with the consideration of its impact on the resilient beam-column nodes. Subsequently, a scaled-down test model is built and constructed, consisting of three stories with a height of 1.2 m and a 2 × 2 span configuration, in accordance with the aforementioned design methodology. The experimental study involved conducting unidirectional shaking table tests on the model in both horizontal directions. The scaled-down model was subjected to seismic excitations of varying intensities, ranging from an 8-degree multiple-occurrence earthquake to a 9-degree rare-occurrence earthquake. Additionally, an extremely rare-occurrence earthquake with an acceleration of 0.75 g was also applied to the model. The test results indicate that the beam-column node exhibits a maximum opening of 4.56 mm and an angle of rotation of 3.04%. Furthermore, the seismic isolation building system demonstrates the ability to accommodate the "expansion effect" of the resilient structure, while simultaneously maintaining load carrying capacity and effectively transmitting horizontal forces. The seismic isolation floor exhibits a notable reduction of 54.8% in its maximum horizontal inertia force, hence demonstrating a favourable damping effect. Based on the observed alterations in the X-direction frequency of the structure prior to and after to the seismic event with a PGA of 0.07 g, it can be inferred that the beam-column connections inside the structure may be deemed as stiff when subjected to several earthquakes. In the PGA = 0.75 g scenario, the maximum interstory displacement angle of 1/69 is observed in the X direction of the 2nd floor. This value is in close proximity to the elastic-plastic interstory displacement angle of 1/50. However, there is no visible deformation or damage to the structure as a whole, and the strain of each member remains within the elastic range, not exceeding 1675 με. Hence, it is widely acknowledged that the resilient steel frame, equipped with a seismic isolation floor system, exhibits robust post-earthquake functional resilience in the face of unidirectional seismic activity.

Generic Vertical Frame Model for Estimation of Floor Vertical Vibration

Response Spectra of Two-Story Frames with Racks on the Elastic Floor

A Horizontal Vibration Wave Model for High Speed Elevators

Peak Acceleration Response Spectrum of Long Span Floor Vibration by Pedestrian Excitation

Floor acceleration amplification and response spectra of reinforced concrete frame structure based on shaking table tests and numerical study

VIBRATION COMFORT ANALYSIS AND DESIGN OF CONCRETE FLOOR BASED ON ANNOYANCE RATE

Floor acceleration control of super‐tall buildings with vibration reduction substructures

Vibration Serviceability Analysis of Floor Structures under Pedestrian Loads

The Transmission Characteristics and Influence Prediction of Impulsive Vibration Caused by a Solid Metal Ball Impact in Buildings

Vertical Vibration of Complex and Slender Footbridges Due to Stochastic Crowd-Induced Excitation

VIBRATION ANALYSIS OF BASE-ISOLATED BUILDING NEAR URBAN RAIL TRANSIT

Effect of Vertical Vibration on Story Drift, Column Axial Force and Beam Acceleration of Steel Moment Frames Subjected to Near-Fault Motions

Analysis of an Isolation System with Vertical Spring-viscous Dampers in Horizontal and Vertical Ground Motion

Seismic responses analysis of multi-story suspended floors system

Seismic Performance Assessment of Ordinary Moment Resisting Frame Equipped with Viscous Dampers under Pulse-Like Earthquakes

Dynamic parameters of structures extracted from ambient vibration measurements: An aid for the seismic vulnerability assessment of existing buildings in moderate seismic hazard regions

A Simplified Beam-Like Model for the Dynamic Analysis of Multi-storey Buildings

Model updating of a shear‐wall tall building using various vibration monitoring data: Accuracy and robustness

One-way shaking table test study of resilient steel frame with seismic isolated floor system

Optimization & Design of High Rise Building with Different Structural Framing Systems Subjected To Seismic Loads

Shaking table experiments on framed structure resting on geogrid reinforced geotechnical seismic isolation system