Abstract:Tungsten carbide (WC), celebrated for its exceptional strength, hardness, and chemical inertness, serves as an exemplary reinforcement for copper (Cu) matrix composite (CMC) coatings, significantly enhancing their wear and corrosion resistance. However, the inherent poor wettability and interfacial bonding between WC and Cu during the cold spray additive manufacturing process pose challenges to further performance improvement of these coatings. This study investigates cold-sprayed CMC coatings reinforced with WC particles, both with and without an electroless plated cobalt (Co) shell (Co@WC; at 10 wt.% and 20 wt.%), focusing on their microstructure, mechanical properties, tribological behavior, and electrochemical corrosion resistance. The findings indicate a reduction in CMC coatings` porosity and mean free path (MFP) of reinforcement particles with increasing reinforcement content. Despite slight Co shell damage during deposition, ceramic retention is notably enhanced, reaching up to 149.3%. The microhardness and wear resistance of CMC coating are improved with decreased MFP and increased ceramic content. Compared to the Cu coating, the microhardness of CMC coatings escalates by up to 32.9% (151.8HV0.1), and the specific wear rate is dramatically reduced by up to 84.2%. The Co shell effectively prevents the detachment of Co@WC particles, thereby enhancing the bending and wear resistance. Electrochemical corrosion tests, encompassing open circuit potential (EOCP), polarization curve, and electrochemical impedance spectroscopy (EIS), indicate that lower porosity, high ceramic content and the Co shell substantially boost the corrosion resistance of the CMC coating. Specifically, the coating with 20 wt.% Co@WC (Cu20(Co@WC)) demonstrates superior corrosion resistance compared to the Cu coating, hinting at the potential for further enhancement with increased ceramic content.

Influence of NbC-doping on the microstructure and thermo-mechanical properties of tungsten coating fabricated by supersonic atmospheric plasma spraying

Influence of Surface Morphology and Microstructure on Performance of CVD Tungsten Coating under Fusion Transient Thermal Loads

Effects Of Wc Crystal Characteristics On Microstructure And Mechanical Property Of Hvof-Sprayed Wc-Cocr Coatings

Lanthanum Hydride Doped Tungsten-Based Coating Fabricated by Supersonic Atmospheric Plasma Spraying

Cold-sprayed Cu Matrix Composite Coatings with Core-Shell Structured Co@WC Reinforcements on Q235 Steel

Effect of NbC in-situ synthesis on the microstructure and properties of pre-placed WCoB-TiC coating by laser cladding

Comparison of plasma sprayed NbB2-NbC coatings obtained by ex-situ and in-situ approaches

Comparison of W–TiC Composite Coatings Fabricated by Atmospheric Plasma Spraying and Supersonic Atmospheric Plasma Spraying

TEM characterization and reaction mechanism of composite coating fabricated by plasma spraying Nb–SiC composite powder

Hard and tough nitrogen doped tungsten coatings deposited by HIPAC: Microstructure and mechanical properties

Microstructure and Tribological Properties of Laser-Remelted Ni-Based WC Coatings Obtained by Plasma Spraying

Effect of nano‐Al 2 O 3 on the microstructure and properties of NbB 2 ‐NbC composite coatings prepared by plasma spraying

In-situ synthesis, microstructure, and properties of NbB2-NbC-Al2O3 composite coatings by plasma spraying

Thermal Performance and Microstructure of Vacuum Plasma Sprayed Tungsten Coatings under Cyclic Heat Load

Microstructure and properties of niobium carbide composite coatings prepared by plasma spraying

Thermal-induced evolution of microstructure as a plasma arc coating Direction-Dependent phenomenon

Plasma sprayed CoNiCrMoNb(BSi) high-entropy amorphous alloy coating: The effect of spraying power on microstructure, mechanical and tribological properties

Study of Thick Tungsten Coatings Deposited on Various Molybdenum and Copper Substrates

TEM characterization and toughening mechanism of in-situ NbB2-NbC-Al2O3 composite coatings prepared by plasma spraying

Effect of C/N incorporation on structural and crystallographic properties of TaNbZr coatings deposited by double-glow plasma surface alloying on Ti-alloy substrate

Rare earth effect on microstructure, mechanical and tribological properties of CoCrW coatings