Abstract:Multi-material fused deposition 3D printing has the unique ability to maintain complex shapes and add special properties. However, the narrow selection of consumable materials, low printing efficiency, and poor performance of the finished products limit the application scope of this technology. In this paper, we propose a twin-screw extrusion 3D printing system that can print a variety of powdered or granular materials, including environmentally friendly biomass particles, metal particles, and thermoplastics, and that enables the mixing of heterogeneous materials. Then we investigate the heat transfer and rheological properties of the system’s material extrusion process. Through the coupled thermal-fluid-solid multi-physical field simulation of the nozzle system, we qualitatively and quantitatively study the transport law and thermal flow field distribution characteristics of the material within the extrusion system, analyze the transport and melting mechanism of the hot melt in the runner during the extrusion process, and obtain the mechanism of the influence of the structural design parameters and the 3D printing process parameters on the transient flow field characteristics and mixing performance. When the screw’s outer diameter is 20 mm and the speed range is 5–25 r/min, the nozzle extrusion flow rate is 2.45–20.15 mm3/s, and the printing efficiency is 3–4 times that of traditional wire printing. The flow field characteristic parameters are optimal when the screw lead is 24–36 mm, and the material extrusion effect is best when the rotational speed is 8–15 r/min. The heat flow field distribution in the extrusion system is stable, the speed distribution is reasonable, and the temperature field distribution is uniform. There is no solution reflux or overflow at the nozzle, the nozzle is not blocked, and the material can be extruded at constant temperature and pressure. The strength of the twin-screw is within the allowable range, the mixing performance is good, and the material can be transported forward with positive displacement. The maximum thermal deformation of the nozzle is 0.09861 mm, which is much smaller than the maximum deformation precision of 0.2 mm, indicating that the screw and nozzle are reasonably designed. The simulation proves the reasonableness of the calculation results.

Ductile forming of polymers by inducing torsional flow to enhance heat transfer and mixing

Heat Transfer and Viscous Polymer Melting Capacity Correlation in Self-Controlled Torsion Induced Extrusion

Enhancing Mixing and Thermal Management of Recycled Carbon Composite Systems by Torsion-Induced Phase-to-Phase Thermal and Molecular Mobility

Enhancing a Multi-Field-synergy Process for Polymer Composite Plasticization: A Novel Design Concept for Screw to Facilitate Phase-to-phase Thermal and Molecular Mobility

Mixing and Thermal Transport Behavior in a Pin or Non-Pin Extruder Equipped with a Field Synergy Elongation Screw

Threading Behavior and Dynamics of Ring-Linear Polymer Blends under Poiseuille Flow

Study on Simulation of Molten Polymer Flow in the Screw Groove

Structural design and heat transfer analysis of twin-screw extrusion 3D printer

Study on Polymer Flow Profile in Micro Hot Embossing

Morphing Pasta and Beyond

3‐D numerical simulations for polycondensation of poly(p‐phenylene terephthalamide) in twin screw extruder

Development of pulsating extensional stress induced melt mixer and its application for polypropylene/carbon fibers composites

Investigation into the Shear Effect of Torsion Extrusion Process

Extreme thermodynamics with polymer gel tori: harnessing thermodynamic instabilities to induce large-scale deformations

Effect of Dynamic Center Region on the Flow and Mixing Efficiency in a New Tri-Screw Extruder Using 3D Finite Element Modeling

Preferential alignment of two-dimensional montmorillonite in polyolefin elastomer tube via rotation extrusion featuring biaxial stress field

Generalized predictions of the pumping characteristics and viscous dissipation of single‐screw extruders including three‐dimensional curvature effects

Mixing screw design and high density polyethylene toughening modification for recycled polypropylene based on screw 3D printing

Modeling and finite element simulation of polypropylene behavior under severe plastic deformation by high-pressure torsion

Numerical design of distributive mixing elements

Two-relaxation-time lattice Boltzmann model of the velocity profiles and volumetric flow rate of generalized Newtonian fluids in a single-screw extruder