Abstract:Amorphous thermoplastic polymers are important engineering materials; however, their non-linear, strongly temperature- and rate-dependent elastic-viscoplastic behavior is still not very well understood, and is modeled by existing constitutive theories with varying degrees of success. There is no generally agreed upon theory to model the large-deformation, thermo-mechanically-coupled, elastic-viscoplastic response of these materials in a temperature range which spans their glass transition temperature. Such a theory is crucial for the development of a numerical capability for the simulation and design of important polymer processing operations, and also for predicting the relationship between processing methods and the subsequent mechanical properties of polymeric products. In this paper we extend our recently published theory [Anand, L., Ames, N. M., Srivastava, V., Chester, S. A., 2009. A thermo-mechanically-coupled theory for large deformations of amorphous polymers. Part I: formulation. International Journal Plasticity 25, 1474–1494; Ames, N. M., Srivastava, V., Chester, S. A., Anand, L., 2009. A thermo-mechanically coupled theory for large deformations of amorphous polymers. Part II: applications. International Journal of Plasticity 25, 1495–1539] to fill this need.We have conducted large strain compression experiments on three representative amorphous polymeric materials – a cyclo-olefin polymer (Zeonex-690R), polycarbonate (PC), and poly(methyl methacrylate) (PMMA) – in a temperature range from room temperature to approximately 50°C above the glass transition temperature, ϑg, of each material, in a strain-rate range of ≈10-4 to 10-1s-1, and compressive true strains exceeding 100%. We have specialized our constitutive theory to capture the major features of the thermo-mechanical response of the three materials studied experimentally.We have numerically implemented our thermo-mechanically-coupled constitutive theory by writing a user material subroutine for a widely used finite element program. In order to validate the predictive capabilities of our theory and its numerical implementation, we have performed the following validation experiments: (i) a plane-strain forging of PC at a temperature below ϑg, and another at a temperature above ϑg; (ii) blow-forming of thin-walled semi-spherical shapes of PC above ϑg; and (iii) microscale hot-embossing of channels in Zeonex and PMMA above ϑg. By comparing the results from this suite of validation experiments of some key features, such as the experimentally-measured deformed shapes and the load-displacement curves, against corresponding results from numerical simulations, we show that our theory is capable of reasonably accurately reproducing the experimental results obtained in the validation experiments.

Modeling and finite element simulation of polypropylene behavior under severe plastic deformation by high-pressure torsion

A Constitutive Model for Strain Hardening Behavior of Predeformed Amorphous Polymers: Incorporating Dissipative Dynamics of Molecular Orientation

High-Pressure Torsion Deformation Induced Phase Transformations and Formations: New Material Combinations and Advanced Properties

Application of an interpenetrating network model to the solid deformation of a quenched isotactic polypropylene film

Severe Plastic Deformation of Light Metals (Magnesium, Aluminum and Titanium) and Alloys by High-Pressure Torsion: Review of Fundamentals and Mechanical/Functional Properties

Thermomechanical Response of Commercially Pure Titanium under Large Plastic Deformation at High Strain Rates

Influence of Processing Parameters on the Mechanical Properties of HPT-Deformed Nickel Carbon Nanotube Composites

Influence of grain shape and orientation on the mechanical properties of high pressure torsion deformed nickel

The self-similarity theory of high pressure torsion

Application of an Interpenetrating Network Model to the Necking in the Microcrystalline Region in Four Annealed Isotactic Polypropylene Films Subjected to Uniaxial Stretching at Room Temperature

Incremental high pressure torsion as a novel severe plastic deformation process: Processing features and application to copper

Evaluating High Pressure Torsion Scaleup

On the reinforcement homogenization in CNT/metal matrix composites during severe plastic deformation

The effect of strain rate on the viscoplastic behavior of isotactic polypropylene at finite strains

A thermo-mechanically-coupled large-deformation theory for amorphous polymers in a temperature range which spans their glass transition

The Evolutions of Microstructure, Texture and Hardness of A1050 Deformed by HPT at the Transition Area

Temperature and strain rate effects on ultra‐high‐molecular‐weight‐polyethylene compression: An experimental and modeling approach

Nanostructuring of Additively Manufactured 316L Stainless Steel Using High-Pressure Torsion Technique: An X-ray Line Profile Analysis Study

Microstructural evolution and mechanical properties of biomedical Co-Cr-Mo alloy subjected to high-pressure torsion

Microstructural and material property changes in severely deformed Eurofer-97

A Comparative Study of a Machine Learning Approach and Response Surface Methodology for Optimizing the HPT Processing Parameters of AA6061/SiCp Composites