Abstract:Multi-material fused deposition 3D printing has the unique ability to maintain complex shapes and add special properties. However, the narrow selection of consumable materials, low printing efficiency, and poor performance of the finished products limit the application scope of this technology. In this paper, we propose a twin-screw extrusion 3D printing system that can print a variety of powdered or granular materials, including environmentally friendly biomass particles, metal particles, and thermoplastics, and that enables the mixing of heterogeneous materials. Then we investigate the heat transfer and rheological properties of the system’s material extrusion process. Through the coupled thermal-fluid-solid multi-physical field simulation of the nozzle system, we qualitatively and quantitatively study the transport law and thermal flow field distribution characteristics of the material within the extrusion system, analyze the transport and melting mechanism of the hot melt in the runner during the extrusion process, and obtain the mechanism of the influence of the structural design parameters and the 3D printing process parameters on the transient flow field characteristics and mixing performance. When the screw’s outer diameter is 20 mm and the speed range is 5–25 r/min, the nozzle extrusion flow rate is 2.45–20.15 mm3/s, and the printing efficiency is 3–4 times that of traditional wire printing. The flow field characteristic parameters are optimal when the screw lead is 24–36 mm, and the material extrusion effect is best when the rotational speed is 8–15 r/min. The heat flow field distribution in the extrusion system is stable, the speed distribution is reasonable, and the temperature field distribution is uniform. There is no solution reflux or overflow at the nozzle, the nozzle is not blocked, and the material can be extruded at constant temperature and pressure. The strength of the twin-screw is within the allowable range, the mixing performance is good, and the material can be transported forward with positive displacement. The maximum thermal deformation of the nozzle is 0.09861 mm, which is much smaller than the maximum deformation precision of 0.2 mm, indicating that the screw and nozzle are reasonably designed. The simulation proves the reasonableness of the calculation results.

Structural design and heat transfer analysis of twin-screw extrusion 3D printer

DEVELOPMENT OF THE METHOD OF DESIGNING THE MICRO SCREW EXTRUDER OF A 3D PRINTER

A Systematic Thermal Analysis for Accurately Predicting the Extrusion Printability of Alginate-Gelatin-Based Hydrogel Bioinks

Stabilization of Filament Production Rate for Screw Extrusion-Based Polymer 3D-Printing

The Research of Technical Solutions of the New Plastic Particles 3D Printer

Computational Study of Extrusion Bioprinting with Jammed Gelatin Microgel-Based Composite Ink

The development of a conical screw-based extrusion deposition system and its application in fused deposition modeling with thermoplastic polyurethane

Investigation on the Temperature Distribution Uniformity of an Extrusion-Based 3D Print Head and Its Temperature Control Strategy

Multimaterial Extrusion of Programmable Periodic Filament Structures Via Modularly Designed Extruder Heads

Rotational Co-extrusion 4D Printing of Heterogeneous Filaments to Enable Sophisticated Shape Morphing

Experimental and numerical characterization of screw elements used in twin-screw extrusion

Design of Extruder with Metering Section Removed and Replaced with Gear Pump for Machine Space Savings in Large Format Additive Manufacturing

Optimization of the extrusion rate for different layer thicknesses to achieve controlled mechanical properties in MEX 3D printing of low-alloy steel

Research Progress on Numerical Modeling of Flow Field and Operating Parameters in Twin Screw Extruder

Mixing and Thermal Transport Behavior in a Pin or Non-Pin Extruder Equipped with a Field Synergy Elongation Screw

Development of Screw-Based 3D Printing Machine and Process Experiments for Short Fiber Reinforced Polymer Composites

Multi-scale modeling and simulation of additive manufacturing based on fused deposition technique

Process Parameter Optimization of Extrusion-Based 3D Metal Printing Utilizing PW–LDPE–SA Binder System

Coupled thermal-force finite element analysis for a twin-screw extruder barrel with two heating pipelines in the axial direction

Experimental Investigation and Numerical Simulations of Temperature and Morphology in Material Extrusion Additive Manufacturing

Effect of Dynamic Center Region on the Flow and Mixing Efficiency in a New Tri-Screw Extruder Using 3D Finite Element Modeling