Abstract:Multi-material fused deposition 3D printing has the unique ability to maintain complex shapes and add special properties. However, the narrow selection of consumable materials, low printing efficiency, and poor performance of the finished products limit the application scope of this technology. In this paper, we propose a twin-screw extrusion 3D printing system that can print a variety of powdered or granular materials, including environmentally friendly biomass particles, metal particles, and thermoplastics, and that enables the mixing of heterogeneous materials. Then we investigate the heat transfer and rheological properties of the system’s material extrusion process. Through the coupled thermal-fluid-solid multi-physical field simulation of the nozzle system, we qualitatively and quantitatively study the transport law and thermal flow field distribution characteristics of the material within the extrusion system, analyze the transport and melting mechanism of the hot melt in the runner during the extrusion process, and obtain the mechanism of the influence of the structural design parameters and the 3D printing process parameters on the transient flow field characteristics and mixing performance. When the screw’s outer diameter is 20 mm and the speed range is 5–25 r/min, the nozzle extrusion flow rate is 2.45–20.15 mm3/s, and the printing efficiency is 3–4 times that of traditional wire printing. The flow field characteristic parameters are optimal when the screw lead is 24–36 mm, and the material extrusion effect is best when the rotational speed is 8–15 r/min. The heat flow field distribution in the extrusion system is stable, the speed distribution is reasonable, and the temperature field distribution is uniform. There is no solution reflux or overflow at the nozzle, the nozzle is not blocked, and the material can be extruded at constant temperature and pressure. The strength of the twin-screw is within the allowable range, the mixing performance is good, and the material can be transported forward with positive displacement. The maximum thermal deformation of the nozzle is 0.09861 mm, which is much smaller than the maximum deformation precision of 0.2 mm, indicating that the screw and nozzle are reasonably designed. The simulation proves the reasonableness of the calculation results.

Mixing screw design and high density polyethylene toughening modification for recycled polypropylene based on screw 3D printing

Direct 3D Printing of Recycled PET/PP Granules by Shear Screw Extrusion

Recycled polypropylene blends as novel 3D printing materials

Multi‐material distributed recycling via material extrusion: recycled high density polyethylene and poly (ethylene terephthalate) mixture

Compatibility study of recycled Polypropylene (PP)/Poly(ethylene terephthalate) (PET) blends nanocomposites with PP‐g‐MAH: Modeling of twin screw extrusion

Subtle Differences in Recycled Polypropylene from Rheology to Additives Impacts Ease of Circularity in Materials Extrusion Additive Manufacture

On the 3D printing of polypropylene and post-processing optimization of thermomechanical properties

Optimization of Glass-Powder-Reinforced Recycled High-Density Polyethylene (rHDPE) Filament for Additive Manufacturing: Transforming Bottle Caps into Sound-Absorbing Material

Structural design and heat transfer analysis of twin-screw extrusion 3D printer

A Promising Recycling Strategy via Processing Polypropylene/Recycled Poly(ethylene terephthalate): Reactive Extrusion Using Dual Compatibilizers

The experiment and simulation of enhanced mechanical performance for polyethylene terephthalate/high‐density polyethylene composites via domain size control

Thinking Green on 3D Printing: Sustainable Polymer Compositions of Post-Consumer Polypropylene and Tire Rubber Crumbs Intended for Industrial Applications

Upcycling waste polypropylene with basalt fibre reinforcement enhancing additive manufacturing feedstock for advanced mechanical performance

Plastic Waste Valorization for Fused Deposition Modeling Feedstock: A Case Study on Recycled Polyethylene Terephthalate/High-Density Polyethylene Sustainability

From Nautical Waste to Additive Manufacturing: Sustainable Recycling of High-Density Polyethylene for 3D Printing Applications

Mechanical Properties and Applications of Recycled Polycarbonate Particle Material Extrusion-Based Additive Manufacturing

Precision control and parameter optimization in screw extrusion 3D printing of polypropylene materials

Thermo-mechanical recycling via ultrahigh-speed extrusion of film-grade recycled LDPE and injection molding

The impact of the glass microparticles features on the engineering response of isotactic polypropylene in material extrusion 3D printing

Short basalt fibre reinforced recycled polypropylene filaments for 3D printing

Creating Sustainable Composites from Pyrolyzed Burlap and Ocean-Recycled Plastics using FDM