Abstract:Ultra‐highly porous and mechanically strong materials are made by tuning interfacial chemistry of the nanoparticle suspensions. The introduced ethanol assists the surfactant to be adsorbed onto the silica surface with enhanced efficiency. High energy of attachment of the nanoparticles improves the stability of the Pickering system. The strong interactions within the foam endow the green bodies with mechanical strengths as well. Highly porous foam ceramics exhibit broad prospects for multifunctional applications. With the facile Pickering‐based foaming technique, wet foams consisting of nanoparticles (NPs) may exhibit high strengths. However, they also experience linear shrinkages as high as 50% after drying and sintering process. Suitable solutions for improving this situation have not been found yet. This work develops a method for fabricating NP‐made foam ceramics by tuning the interfacial chemistry of this Pickering system. Trace amounts of ethanol are used to adjust the adsorbing behavior of surfactants on the silica surface to enhance the energy of attachment of the Pickering systems. Combined with the altered capillary forces, the linear shrinkages of the foam ceramic are considerably lowered. The pore wall of the obtained foam ceramics can be tuned to either closed or open due to the "coffee ring" effect by adjusting the solid content and sintering temperature. The samples present high thermal insulating properties and high mechanical strength even the unsintered ones, which also show good stability in liquid environments. Combined with the direct ink writing (DIW) technique, these freely shaped materials with tunable pore structures can be readily exploited in tissue scaffolds, catalyst carriers, thermal insulators, battery electrodes, and liquid/gas filtration, etc.

Ultralight and Mechanically Robust SiC Foams with Interconnected Cellular Architecture

Highly Porous Alumina Cellular Ceramics Bonded by In-Situ Formed Mullite Prepared by Gelation-Assisted Al2O3–Si Particle-Stabilized Foams

Mullite Ceramic Foams with Tunable Pores from Dual-Phase Sol Nanoparticle-Stabilized Foams

Highly Porous and Mechanically Robust Al2O3-based Foams with Self-Wrinkled and Rough Aperture Surfaces Via Binary Colloidal Self-Assembly of Nanoparticle/gelation Network

Highly Porous and Hierarchical MgAl2O4 Ceramics with Improved Pore Connectivity Prepared from Gelled Particle-Stabilized Foams

A Novel Method of Strong and Tough Si3N4 Ceramic from the Particle‐stabilized Foam

Pore Structure Control of Si3n4 Ceramics Based on Particle-Stabilized Foams

Preparation and Characterization of SiO2/Carbon Foam and SIC/Carbon Foam Composites

Mechanically Robust ZrO2 Foams with 3D Reticular Architecture Prepared from Chemical‐modified ZrO2 Powder

Ultrahigh‐strength Alumina Ceramic Foams Via Gelation of Foamed Boehmite Sol

Silica Foams With Ultra-Large Specific Surface Area Structured By Hollow Mesoporous Silica Spheres

Ceramic foams with highly open channel structure from direct foaming method in combination with hollow spheres as pore-former.

High-strength, 3D interconnected alumina ceramic foams with high porosity comparable to aerogels

Light and strong nano-SiC foam with extremely low thermal conductivity

Facile Fabrication of Nanofibrous Network Reinforced Hierarchical Structured Porous Si3N4-based Ceramics Based on Si-Si3N4 Binary Particle-Stabilized Foams

Formation of hierarchical Si3N4 foams by protein-based gelcasting and chemical vapor infiltration

Ultralight Silicon Nitride Ceramic Foams from Foams Stabilized by Partially Hydrophobic Particles

3D Printable Ultra‐Highly Porous and Mechanically Strong Foam Materials for Multiple Applications

Aerogel‐like Ceramic Foams with Super‐high Porosity and Nanoscale Cell Wall from Sol Nanoparticles Stabilized Foams

Ultralight and High-Strength SiC nw @SiC Foam with Highly Efficient Microwave Absorption and Heat Insulation Properties

Study on particle-stabilized Si3N4 ceramic foams