Abstract:A colloidal stability study of a nonaqueous silicon carbide suspension is of great significance for preparing special silicon carbide ceramics by colloidal processing. In this paper, three different chemical dispersants, which are amphiphilic, acidophilic, and alkaliphilic, are selected to compare their ability to stabilize nonaqueous slurries of silicon carbide. The analysis of the flow index factor is first used to estimate the colloidal stability of the suspensions. The results show that the addition of only 5 wt.% polyvinylpyrrolidone (PVP) forms a silicon carbide slurry with a low viscosity value of 17 mPa⋅s at 25 s−1. In addition, Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS)measurements indicate that the PVP molecule is successfully adsorbed on the surface of silicon carbide. The different adsorption models are fitted, and the adsorption of PVP molecules on the surface of silicon carbide belongs to the Langmuir single-layer adsorption model. At the optimal PVP amount, the volume content of the suspension is as high as 22.27 vol.%, a Newtonian-like fluid still appears, and no agglomerate structure is formed in the system. After the volume content exceeds 22.27 vol.%, the flow index factor of the slurry begins to plummet, indicating that the slurry begins to transform from a Newtonian-like fluid to a shear-thinning fluid. The particles undergo inevitable agglomeration accompanied by the emergence of yield stress. Finally, a maximum solid loading of the system is predicted to be 46 vol.%, using the Krieger-Dougherty model.

Study on the Rheology of Acetic Acid Modified SiC Powder and Pastes Reinforced by Solvothermal Method

Surface Modification of Halloysite/Sericite

Surface modification of superfine SiC powders by ternary modifiers-KH560/sodium humate/SDS and its mechanism

Study on Rheological Behavior of Micro/Nano-Silicon Carbide Particles in Ethanol by Selecting Efficient Dispersants

Aqueous Processing, Hot-Pressing and Mechanical Properties of Silicon Carbide with Al2O3 and Y2O3

Effects of Powder Surface Modification and Amount of Oxide Additives on Rheological Property of Si<sub>3</sub>N<sub>4</sub> Aqueous Suspension

Influence of surface oxide layer of SiC powder on the rheological properties of its slurry

Study on preparation and surface modification of precipitated silica obtained from fly ash

Effect of Acid Cleaning and Calcination on Rheological Properties of Concentrated Aqueous Suspensions of Silicon Nitride Powder

Composite modification of fine SiC powder by 3-aminopropyl triethoxysilane and sodium polystyrene sulfonate and its slip casting study

Effect and mechanism of ultrasound on acid loading in the preparation of silicon-based sulfonic solid acids

Surface modification of Cu-coated carbon fiber for improved mechanical performance of Acrylonitrile Butadiene Styrene composites using 3-Aminopropyl triethoxy silane

Influence of Silane Coupling Agent and Anionic Dispersant on the Dispersion Effect of Silicon Carbide Particles

Using acetic acid as a preconditioner to optimize rheology of alkali-activated coal gasification slag based backfill pastes

Simultaneous improvement of interfacial bonding and thermal resistance of carbonaceous fiber/silicone composite coatings modified with aniline-methyl-triethoxysilane

The effects of surfactants on CIM of Si3N4

Synthesis and characterization of amorphous silica-alumina with enhanced acidity and its application in hydro-isomerization/cracking

Rheological properties and thixotropy model of concentrated aqueous silicon slurry for gel casting

Preparation of CIM Feedstock of Al2O3-SiC Nanocomposite

Morphological and mineralogical insights into acetic acid modifying and hydraulic process on steel slag for enhanced reactivity

Effect of TMAH on Rheological Behavior of SiC Aqueous Suspension