Abstract:Selective laser sintering (SLS) combined with reaction melt infiltration was used to fabricate Si–SiC ceramic matrix composites, and the effects of different concentrations of phenolic resin (PF) on the properties of the SLS green body and carbonized and final Si–SiC samples were investigated. The results showed that the impregnation with PF can increase the bulk density, reduce the porosity of the samples at all stages, and improve the mechanical properties of the reactive bonded samples. The degree of densification and mechanical properties of the sample gradually enhanced with an increase in PF concentration. The main phases of the Si–SiC composites were free Si, α-SiC, β-SiC, plus an extremely small amount of Al–Si alloy, and the SiC and the Si phase contents increased and decreased, respectively, as the concentration of PF increased when measured using Rietveld refinement and image analysis software. The macroscopic properties of the samples improved greatly after precursor infiltration pyrolysis (PIP) treatment with 66.7%vol PF-ethanol solution twice. According to the crystal nucleation-growth theory, it was inferred that the infiltrated PF could provide a certain amount of pyrolytic carbon in the carbonized specimen. During the reaction bonded process, the carbon formed by carbonization pyrolysis first dissolves into the molten Si and reaches saturation. With the further dissolution of carbon, [C] and [Si] in the liquid phase contact each other to form β-SiC nuclei, the nuclei that precipitate at the pore wall position and gradually form a continuous interfacial layer of β-SiC. The β-SiC layer prevents the liquid Si from direct contact with C inside the prefabricated body, therefore, further reactants diffuse through the layer. Finally, the fine crystalline β-SiC grains were fabricated inside the specimen.

Composite modification of fine SiC powder by 3-aminopropyl triethoxysilane and sodium polystyrene sulfonate and its slip casting study

Surface modification of superfine SiC powders by ternary modifiers-KH560/sodium humate/SDS and its mechanism

Influence of Silane Coupling Agent and Anionic Dispersant on the Dispersion Effect of Silicon Carbide Particles

Carbon-bonded Carbon Fiber Composites Containing Uniformly Distributed Silicon Carbide

Enhancing mechanical properties of selectively laser sintered SiC/Si composites printed using electrostatic spraying microspheres with fine particles

Effect of impregnated phenolic resin on the properties of Si–SiC ceramic matrix composites fabricated by SLS-RMI

DISPERSIBILITY MECHANISM AND SPRAY DRYING OF SiC AQUEOUS SLURRY

Aqueous Processing, Hot-Pressing and Mechanical Properties of Silicon Carbide with Al2O3 and Y2O3

Study on gelcasting and properties of recrystallized silicon carbide

Enhanced Molding and Mechanical Properties of SiC-based Ceramic Lattice Structures Via Digital Light Processing

Gelcasting of Concentrated Aqueous Silicon Carbide Suspension

Direct Coagulation Casting of Silicon Carbide Suspension Via Polyelectrolyte Dispersant Crosslink Reaction

EFFECT OF AL(2)O(3) AND SIC CONTENT IN PACK CEMENTATION POWDERS ON THE MICROSTRUCTURE OF SIC COATINGS ON HTR GRAPHITE SPHERES

Controllable reduction of absorbance and two-step reaction for 3D-printed SiC ceramics with micron-level periodic structure

Preparation of silicon carbide ceramics using chemical treated powder by DCC via dispersant reaction and liquid phase sintering

Fabrication and Mechanical Properties of SiCw(p)/SiC-Si Composites by Liquid Si Infiltration using Pyrolysed Rice Husks and SiC Powders as Precursors

Pretreatment Process of SiC Particles and Fabrication Technology of SiC Particulate Reinforced Zn–Al Alloy Matrix Composite

Densification and Enhancement of Sic Particulate Reinforced Fine Grain Sic Ceramic

Influence of characteristic parameters of SiC reinforcements on mechanical properties of AlSi10Mg matrix composites by powder metallurgy

Bimodal powder optimization in SiC binder jetting for mechanical performance

A novel sintering additive system for porous mullite-bonded SiC ceramics: High mechanical performance with controllable pore structure