Abstract:Thermal spray cermet based on tungsten carbide has been widely used due to its excellent wear resistance. The features of both carbide and binder phases are essential factors which determine the performance of cermet coating. The thermal cycling of WC–Co spray particles up to a temperature over the melting point of binder phase during thermal spraying involves the decarburization of carbide. The decarburization of carbide becomes severe with the decrease of carbide particle size, which makes it difficult yet to deposit a dense nanostructured WC–Co with a limited decarburization by thermal spraying. The decarburization not only reduces the wear-resistant phase but also leads to the formation of brittle Co–W–C ternary binder phase. Moreover, the limited decarburization involves the deposition of spray particle at a solid–liquid two-phase state with carbides at a solid state and metal binder in a molten state during spraying. High velocity impact of two-phase droplets as in high velocity oxy-fuel spraying (HVOF) results in the formation of a dense cermet coating and on the other hand leads to the possibility of rebounding of wear-resistant solid carbide particles. In this review article, the microstructural features of thermal spray WC–Co are examined based on the effect of the decarburization of tungsten carbide. The decarburization mechanisms of tungsten carbide are discussed for the control of decarburization of carbide. The effects of carbide particle size on the deposition process, adhesion of HVOF coating and wear performance of WC–Co coating as well are examined based on a solid–liquid two-phase deposition process. It is demonstrated that WC–Co cermet with different sizes of WC particles should be deposited by different processes. Moreover, the deposition of nanostructured WC–Co by thermal spraying and recent advances on the cold spraying of nanostructured WC–Co are introduced. The cold spraying with the proper design of spray powders will become promising process to deposit nanostructured WC–Co with pure cobalt binder with the hardness comparable to a sintered bulk and even high toughness of 18.9MPam1/2. The pure metastable metal binder phase evolved in the deposit makes it possible to deposit hard cermet through healing the non-bonded interfaces in the coating by post-spray annealing.

A New Strategy to Efficiently Fabricate Tungsten Carbide Coating on Tungsten: Two-step Interstitial Carburization

Fe-coating-mediated carburization: A new strategy for fabricating a tungsten carbide coating on tungsten

Microstructure and Formation Mechanism of WC Coating on Tungsten Fabricated by Interstitial Carburization: A Multiscale Investigation

A Key to Tune the Grain Size Gradient of the TiC Coating on Titanium by Interstitial Carburization: the Timing for Pressing

A new strategy for preparing carbide coatings on easily oxidized tantalum by non-vacuum carburizing: Fe-coating-mediated carburization

Investigation of indentation response, scratch resistance, and wear behavior of tungsten carbide coatings fabricated by two-step interstitial carburization on tungsten

Fabrication of Mo2C Coating on Molybdenum by Contact Solid Carburization

Promising WC-30WB-10Co Cemented Carbide Coating with Improved Density and Hardness Deposited by High Velocity Oxy-Fuel Spraying: Microstructure and Mechanical Properties

A short and facile process to synthesize WC-Co cemented carbides

Dissolving Mechanism of the WC/W2Cp in NiCrBSi Alloy and Surface Modification for the WC/W2Cp by Carburizing

Microhomogeneous WC-TiC-Co composite powders with enhanced sinterability via a two-step carburization method

New strategy to grow TiC coatings on titanium alloy: Contact solid carburization by cast iron

Novel conversion annealing pretreatment for improved deposition of diamond coatings onto WC-Co cemented carbide

Coprecipitation of co and La 2 O 3 coprecipitation on WC for tailoring the grain distribution and boundary of high-performance coarse-grained WC-10Co cemented carbide

Pressureless Two-Step Sintering of Ultrafine-Grained Tungsten

Microstructure and properties of coarse WC-10CoCrFeMnNi cemented carbide by mechanical alloying and hot pressing sintering

Introduction of tungsten carbide into 08Kh18N10T corrosion-resistant steel and its effect on mechanical properties

Carbon control and densification of WC-8%Co fabricated by extrusion-based additive manufacturing under pressureless sintering

Relationships Between Feedstock Structure, Particle Parameter, Coating Deposition, Microstructure and Properties for Thermally Sprayed Conventional and Nanostructured WC–Co

Fabrication and performance of graded ultrafine WC–Co cemented carbide tool by one/two-step spark plasma sintering

WC-Co Composite Coating Deposited by Cold Spraying of a Core-Shell-Structured WC-Co Powder