A Fiber-Shaped Light-Emitting Pressure Sensor for Visualized Dynamic Monitoring

Xufeng Zhou,Xiaojie Xu,Yong Zuo,Meng Liao,Xiang Shi,Chuanrui Chen,Songlin Xie,Peng Zhou,Xuemei Sun,Huisheng Peng

DOI: https://doi.org/10.1039/c9tc05653j

IF: 6.4

2020-01-01

Journal of Materials Chemistry C

Abstract:A fiber-shaped light-emitting pressure sensor is achieved to simultaneously detect and visualize force stimuli in one single device.

What problem does this paper attempt to address?

High-resolution Electroluminescent Imaging of Pressure Distribution Using a Piezoelectric Nanowire LED Array

Caofeng Pan,Lin Dong,Guang Zhu,Simiao Niu,Ruomeng Yu,Qing Yang,Ying Liu,Zhong Lin Wang

DOI: https://doi.org/10.1038/nphoton.2013.191

IF: 35

2013-01-01

Nature Photonics

Abstract:Emulation of the sensation of touch through high-resolution electronic means could become important in future generations of robotics and human–machine interfaces. Here, we demonstrate that a nanowire light-emitting diode-based pressure sensor array can map two-dimensional distributions of strain with an unprecedented spatial resolution of 2.7 µm, corresponding to a pixel density of 6,350 dpi. Each pixel is composed of a single n-ZnO nanowire/p-GaN light-emitting diode, the emission intensity of which depends on the local strain owing to the piezo-phototronic effect. A pressure map can be created by reading out, in parallel, the electroluminescent signal from all of the pixels with a time resolution of 90 ms. The device may represent a major step towards the digital imaging of mechanical signals by optical means, with potential applications in artificial skin, touchpad technology, personalized signatures, bio-imaging and optical microelectromechanical systems.
Single Optical Microfiber Enabled Tactile Sensor for Simultaneous Temperature and Pressure Measurement

Ni Yao,Xiaoyu Wang,Shuqi Ma,Xingda Song,Shan Wang,Zhangxing Shi,Jing Pan,Shipeng Wang,Jianliang Xiao,Haitao Liu,Longteng Yu,Yao Tang,Zhang,Xiong Li,Wei Fang,Lei Zhang,Limin Tong

DOI: https://doi.org/10.1364/prj.461182

IF: 7.6

2022-01-01

Photonics Research

Abstract:The ability to sense heat and touch is essential for healthcare, robotics, and human–machine interfaces. By taking advantage of the engineerable waveguiding properties, we design and fabricate a flexible optical microfiber sensor for simultaneous temperature and pressure measurement based on theoretical calculation. The sensor exhibits a high temperature sensitivity of 1.2 nm/°C by measuring the shift of a high-order mode cutoff wavelength in the short-wavelength range. In the case of pressure sensing, the sensor shows a sensitivity of 4.5% per kilopascal with a fast temporal frequency response of 1000 Hz owing to the strong evanescent wave guided outside the microfiber.The cross talk is negligible because the temperature and pressure signals are measured at different wavelengths based on different mechanisms. The properties of fast temporal response, high temperature, and pressure sensitivity enable the sensor for real-time skin temperature and wrist pulse measurements, which is critical to the accurate analysis of pulse waveforms. We believe the sensor will have great potential in wearable optical devices ranging from healthcare to humanoid robots.
Flexible Liquid-Filled Fiber Adapter Enabled Wearable Optical Sensors

Jing Pan,Chengpeng Jiang,Zhang Zhang,Lei Zhang,Xiaozhi Wang,Limin Tong

DOI: https://doi.org/10.1002/admt.202000079

IF: 6.8

2020-01-01

Advanced Materials Technologies

Abstract:Wearable optical sensors are attracting intensive research interests owing to their advantage of high sensitivity, fast response, and immunity to electromagnetic interferences. However, tunable optical properties and reconfigurable sensor structures remain great challenges for the wearable optical sensors. Herein, flexible liquid-filled fiber adapters (FLFFAs), which are sensitive to mechanical stimuli, are demonstrated. The novel FLFFA consists of a soft liquid-filled tubing and two silica optical fibers. The liquid core bestows the FLFFA both tunability and reconfigurability in sensing performance. Deformation of the tubing through bending or pressing results in wavelength-insensitive changes in light transmission. By measuring the output intensity, the FLFFA based sensors achieve high angle resolution (0.18 degrees) and low detection limit (0.7 mN) for bending and pressure sensing, respectively. The superior sensing properties together with mechanical flexibility and robustness enable real-time monitoring of finger joint motion, respiration, and wrist pulse. Benefiting from an LED charge-coupled device (CCD) signal recording system, a 4 x 3 keyboard is realized by simultaneously measuring the output signals of 12 FLFFAs. The FLFFA provides a promising method to detect subtle physiological signals and may find applications in healthcare devices, artificial skins, and sensor networks.
Mono-Fiber Optic Pressure Sensor

Jun-nan HE,Zhen-xiang CAI,Xue-jin LI,Jin LIU,Huan-bin HUANG

DOI: https://doi.org/10.3969/j.issn.1004-1699.2007.06.022

2007-01-01

Abstract:A mono-fiber optic pressure sensor aimed to reduce the size of sensors is designed. A single optic fiber is used to replace the traditional optic fiber bundle, and to collect the light reflected by an elastic spherical diaphragm, which is part of the light emitted out by itself. The single optic fiber works as emitting light fiber as well as receiving light fiber. The diaphragm coils when force is performed upon, and light intensity received by the fiber changes depending on the deformation of the elastic spherical diaphragm. The relationship between sensitivities of the sensor and the distance from the terminal of fiber to the initial diaphragm before force performed upon are researched experimentally. According to the analysis of virtual light spot, light distributing theory is modified, and it makes the consequence of calculations fit the results of experiment well. The sensor with the unique structure can not only minish the size of sensor but also solve the un-detecting-area problem of multi-fiber optic sensors.
High-Sensitivity Microfiber Strain and Force Sensors

Wei Li,Zhifang Hu,Xiyuan Li,Wei Fang,Xin Guo,Limin Tong,Jingyi Lou

DOI: https://doi.org/10.1016/j.optcom.2013.09.072

IF: 2.4

2014-01-01

Optics Communications

Abstract:A microfiber biconically tapered from a standard optical fiber shows obvious sinusoidal oscillatory transmission spectrum due to the multimode interference, with evident blue-shifted peak wavelength when applying an axial force. Based on this force-induced spectral shift, here we experimentally demonstrate compact microfiber strain and force sensors with low optical power and high sensitivity. With a 1.5-μW probing light, measured sensitivity of a 2.5-μm-diameter microfiber for the strain and elongation sensing are 4.84pm/με and 404pm/μm respectively, with a force detection limit down to 50μN.
A Wearable Pressure Sensor Based on the Array of Polymeric Piezoelectric Fiber with Metal Core.

Ran Chen,Weiting Liu,Xiao-dong Ruan,Xin Fu

DOI: https://doi.org/10.1007/978-3-319-43518-3_12

2016-01-01

Abstract:A wearable pressure sensor is developed based on the array of polymeric piezoelectric fiber with metal core covered by beta phase polyvinylidene fluoride layer. Each fiber consists of a polyester-imide enameled copper core, a piezoelectric layer and sputtered gold electrode. Fiber array is fixed on an insulating substrate and well packaged to ensure stable work. This pressure sensor is tested to declare high sensitivity and fast response. Meanwhile, flexibility of this structure indicates its potentiality to be wearable.
Pressure Visualization and Quantification Photonic Skin Based on Flexible Optical Fiber Combiner

Jie Fang,Hongyan Zheng,Anping Yang,Haojun Liu,Yongcheng He,Hongyou Zhou,Luyan Liu,Enhai Song,Qianyi Guo,Jiulin Gan,Zhongmin Yang

DOI: https://doi.org/10.1002/adfm.202408800

IF: 19

2024-09-21

Advanced Functional Materials

Abstract:A photonic skin based on a flexible optical fiber combiner enables accurate and intuitive pressure measurement. Pressure‐induced changes in the optical fibers' transmission loss alter the output light intensity ratio, causing a color shift at the combiner port for unobstructed pressure quantification and visualization. This wearable system supports various applications, including tactile modes, finger bending, and oral occlusion force detection. The integration of pressure quantification and visualization enhances pressure perception, accuracy, and efficiency. Current solutions require improvements in quantization accuracy, structural simplicity, and integration. We proposed a novel photonic skin comprising a 3 × 1 flexible optical fiber combiner, integrating red, green, and blue light emitting diode (LED) chips through three flexible optical fibers. Under pressure, changes in the optical fibers' transmission loss alter the output light intensity ratio, thus inducing a color shift at the combiner's output. This visible change can be precisely quantified using a color sensor chip. Performance metrics include sensing range up to 33N, sensitivity between 0.04 and 0.24 dB N−1, detection limit below 0.08 N, response time of 500 ms, recovery time of 400 ms, and durability exceeding 2000 cycles. A compact flexible circuit board manages light source driving, data acquisition, and wireless communication, forming a wearable photonic skin system. This system enables visual recognition and quantitative measurement of pressure across diverse scenarios, including different tactile modes, multi‐position pressure, finger bending, and neck movement. For oral occlusion force detection, the spatial separation of the sensing and visualization areas enables the system to simultaneously provide accurate measurements and intuitive visual assessment.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
A Novel High-Sensitivity Fiber Grating Sensor for Simultaneous Measurement of Temperature and Pressure

郑史烈,李静,章献民

DOI: https://doi.org/10.3969/j.issn.1005-5630.2008.05.013

2008-01-01

Abstract:A novel sensor based on a single fiber Bragg grating is described.The sensor is configured by encapsulating half of a fiber Bragg grating in a polymer filled metal cylinder and fixing the other half to the metal cylinder.The fixed part of the fiber Bragg grating is immune to the strain while the other part is sensitive to both the strain and the temperature,therefore the novel structure can realize the separate sense of strain and temperature.Using a novel tactic to transfer the applied pressure to the axial extended-strain on the fiber Bragg grating,the pressure sensitivity can be greatly improved.The results show that this novel sensor can simultaneously measure pressure and temperature,meanwhile the pressure sensitivity reaches to 9.65×10-3MPa-1,which is about 4770 times larger than that of the bare fiber Bragg grating.
High-Resolution Dynamic Pressure Sensor Array Based on Piezo-phototronic Effect Tuned Photoluminescence Imaging

Mingzeng Peng,Zhou Li,Caihong Liu,Qiang Zheng,Xieqing Shi,Ming Song,Yang Zhang,Shiyu Du,Junyi Zhai,Zhong Lin Wang

DOI: https://doi.org/10.1021/acsnano.5b00072

IF: 17.1

2015-01-01

ACS Nano

Abstract:A high-resolution dynamic tactile/pressure display is indispensable to the comprehensive perception of force/mechanical stimulations such as electronic skin, biomechanical imaging/analysis, or personalized signatures. Here, we present a dynamic pressure sensor array based on pressure/strain tuned photoluminescence imaging without the need for electricity. Each sensor is a nanopillar that consists of InGaN/GaN multiple quantum wells. Its photoluminescence intensity can be modulated dramatically and linearly by small strain (0-0.15%) owing to the piezo-phototronic effect. The sensor array has a high pixel density of 6350 dpi and exceptional small standard deviation of photoluminescence. High-quality tactile/pressure sensing distribution can be real-time recorded by parallel photoluminescence imaging without any cross-talk. The sensor array can be inexpensively fabricated over large areas by semiconductor product lines. The proposed dynamic all-optical pressure imaging with excellent resolution, high sensitivity, good uniformity, and ultrafast response time offers a suitable way for smart sensing, micro/nano-opto-electromechanical systems.
Simultaneous Measurement of Pressure and Temperature Using a Single Fiber Bragg Grating

Shilie Zheng,Xianmin Zhang

DOI: https://doi.org/10.2529/piers050318084922

2005-01-01

PIERS Online

Abstract:A novel sensor based on a single fiber Bragg grating is described. The sensor is configured by encapsulating half of a fiber Bragg grating in a polymer filled metal cylinder and fixing the other half to the metal cylinder. The results show that this sensor is able to measure pressure and temperature simultaneously. Using a novel tactic to transfer the applied pressure to the axial extended-strain on the fiber Bragg grating, the pressure sensitivity reaches 9.65×10 −3 MPa −1 , which is about 4700 times larger than that of the bare fiber Bragg grating. The accuracy of the pressure measuring can also be improved through introducing a fixed Bragg wavelength as a reference.
An Optical Fiber Pressure Sensor Based on F-P Interferometry and Intensity Demodulation

DENG Yuan-long,ZHAO Xiao-li,LI Xue-jin,GENG You-fu,HONG Xue-ming,QIU Cheng-jun

DOI: https://doi.org/10.3969/j.issn.1000-2618.2011.01.002

2011-01-01

Abstract:An optical fiber pressure sensor was designed,fabricated and characterized.It employed a Fabry-Perot (F-P) interferometer and simple intensity-demodulation technology.A square silicon cup processed by anisotropic etching serves as sensitive element for the better consistency than that of circular diaphragm.A large area ratio of the moving mirror to the stationary one is introduced to reduce the nonlinearity due to the non-planarity of the deflection.Reference light generated from a 2×2 optical fiber coupler is used to decrease the influence of intensity variations of the light source.Single-value measurement was achieved under the pressure range from 0 to 38 kPa.The experimental results demonstrate an upmost relative sensitivity of 0.7%/kPa and a reasonable repeatability,consisting well with the theoretical analysis and simulation.A new method of multi-wave or multi-sensor is presented to expand the measurement range with high sensitivity.
Self-powered, ultrasensitive, and high-resolution visualized flexible pressure sensor based on color-tunable triboelectrification-induced electroluminescence

Li Su,Zhiye Jiang,Zhen Tian,Hailu Wang,Haojie Wang,Yunlong Zi

DOI: https://doi.org/10.1016/j.nanoen.2020.105431

IF: 17.6

2021-01-01

Nano Energy

Abstract:<p>With the capability of mapping local pressure information and converting it into human-readable visual optical signals simultaneously, self-powered visualized flexible pressure sensor (SP-VFPS) has aroused a new surge of interest because of its good solution to the wireless communication of human stress/strain sensing. Herein, a new class of SP-VFPS based on micro compression-dependent porous architecture was reported to be capable of enabling color-tunable triboelectrification-induced electroluminescence (TIEL) in response to vertical pressure in real time, exhibiting a rather low detection limit of tribo-pressure at ~ 10 kPa, the high sensitivity (S > 190 kPa<sup>−1</sup>) within a wide pressure range as well as a rapid response time of below 10 ms. Through the integration of SP-VFPS with a single-electrode triboelectric nanogenerator (TENG) matrix, the hybrid sensing system was further developed with multi-functional pressure sensitivity for multi-touch sensing, motion monitoring, and high-resolution (500 µm) eye-detectable spatial pressure mapping by a combination of electrical and optical responses. This SP-VFPS is the first demonstration towards color-tunable TIEL as an all-in-one device for the instantaneous detection of pressure information which may provide new insight into its applications in robots, smart sensor networks, future real-time pressure mapping systems, and human-machine interfaces through wireless optical communication.</p>

materials science, multidisciplinary,chemistry, physical,physics, applied,nanoscience & nanotechnology
A Fiber-Optic Pressure Sensor with Reflecting Optical Structure for the Simultaneous Measurement of Temperature

XP Zheng,YB Liao,KD Zha

DOI: https://doi.org/10.1117/12.252163

1996-01-01

Abstract:A novel fiber-optic pressure sensor with reflecting optical structure for the simultaneous measurement of temperature is presented. The operation principle of the sensor is based on the photoelastic effect and the temperature signal is extracted from the fluctuation of the quasi working point of the sensor due to the thermal effect of the wave plate. The wave plate used here is not the 1/4 lambda as used in typical photoelastic pressure sensors in order to obtain the best response of linearity. Two kinds of bridge compensation techniques are used for the pressure and the temperature respectively. The experimental results show that once the temperature is determined, the fluctuation of the pressure output can be eliminated, and more accurate pressure meter is available.
Optoelectronic Pressure Sensor Based on the Bending Loss of Plastic Optical Fibers Embedded in Stretchable Polydimethylsiloxane

Alberto Alonso Romero,Koffi Novignon Amouzou,Dipankar Sengupta,Camila Aparecida Zimmermann,Andréane Richard-Denis,Jean-Marc Mac-Thiong,Yvan Petit,Jean-Marc Lina,Bora Ung

DOI: https://doi.org/10.3390/s23063322

IF: 3.9

2023-03-23

Sensors

Abstract:We report the design and testing of a sensor pad based on optical and flexible materials for the development of pressure monitoring devices. This project aims to create a flexible and low-cost pressure sensor based on a two-dimensional grid of plastic optical fibers embedded in a pad of flexible and stretchable polydimethylsiloxane (PDMS). The opposite ends of each fiber are connected to an LED and a photodiode, respectively, to excite and measure light intensity changes due to the local bending of the pressure points on the PDMS pad. Tests were performed in order to study the sensitivity and repeatability of the designed flexible pressure sensor.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
A Transflective Nano-Wire Grid Polarizer Based Fiber-Optic Sensor

Jing Feng,Yun Zhao,Xiao-Wen Lin,Wei Hu,Fei Xu,Yan-Qing Lu

DOI: https://doi.org/10.3390/s110302488

IF: 3.9

2011-01-01

Sensors

Abstract:A transflective nano-wire grid polarizer is fabricated on a single mode fiber tip by focused ion beam machining. In contrast to conventional absorptive in-line polarizers, the wire grids reflect TE-mode, while transmitting TM-mode light so that no light power is discarded. A reflection contrast of 13.7 dB and a transmission contrast of 4.9 dB are achieved in the 1,550 nm telecom band using a 200-nm wire grid fiber polarizer. With the help of an optic circulator, the polarization states of both the transmissive and reflective lights in the fiber may be monitored simultaneously. A kind of robust fiber optic sensor is thus proposed that could withstand light power variations. To verify the idea, a fiber pressure sensor with the sensitivity of 0.24 rad/N is demonstrated. The corresponding stress-optic coefficient of the fiber is measured. In addition to pressure sensing, this technology could be applied in detecting any polarization state change induced by magnetic fields, electric currents and so on.
Recent Progress in MEMS Fiber-Optic Fabry–Perot Pressure Sensors

Ye Chen,Dongqin Lu,Huan Xing,Haotian Ding,Junxian Luo,Hanwen Liu,Xiangxu Kong,Fei Xu

DOI: https://doi.org/10.3390/s24041079

IF: 3.9

2024-02-08

Sensors

Abstract:Pressure sensing plays an important role in many industrial fields; conventional electronic pressure sensors struggle to survive in the harsh environment. Recently microelectromechanical systems (MEMS) fiber-optic Fabry–Perot (FP) pressure sensors have attracted great interest. Here we review the basic principles of MEMS fiber-optic FP pressure sensors and then discuss the sensors based on different materials and their industrial applications. We also introduce recent progress, such as two-photon polymerization-based 3D printing technology, and the state-of-the-art in this field, e.g., sapphire-based sensors that work up to 1200 °C. Finally, we discuss the limitations and opportunities for future development.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Research on the Fabrication and Parameters of a Flexible Fiber Optic Pressure Sensor with High Sensitivity

Huixin Zhang,Jing Wu,Chencheng Gao

DOI: https://doi.org/10.3390/photonics11100919

IF: 2.536

2024-09-29

Photonics

Abstract:In recent years, flexible pressure sensors have garnered significant attention. However, the development of large-area, low-cost, and easily fabricated flexible pressure sensors remains challenging. We designed a flexible fiber optic pressure sensor for contact force detection based on the principle of backward Rayleigh scattering using a single-mode optical fiber as the sensing element and polymer PDMS as the encapsulation material. To enhance the sensor's sensitivity and stability, we optimized its structural design, parameters, and fabrication process and measured the fiber strain using an optical frequency domain reflectometer (OFDR). The results showed that the sensor achieved a high sensitivity of 6.93247 με/kPa with a PDMS concentration ratio of 10:1, a curing time of 2 h, and a substrate thickness of 5 mm. The sensor demonstrated excellent linearity and repeatability in static performance tests and was successfully used to monitor the plantar pressure distribution in real time. This flexible fiber optic pressure sensor can be developed via a simple fabrication process, has a low cost, and has high sensitivity, highlighting its potential applications in smart wearables and medical diagnostics.

optics
Hybrid Fiber Optic Sensor, Based on the Fabry–Perot Interference, Assisted with Fluorescent Material for the Simultaneous Measurement of Temperature and Pressure

Xiaofeng Jiang,Chun Lin,Yuanqing Huang,Kan Luo,Jianhuan Zhang,Qingshan Jiang,Chentao Zhang

DOI: https://doi.org/10.3390/s19051097

IF: 3.9

2019-03-04

Sensors

Abstract:Herein we design a fiber sensor able to simultaneously measure the temperature and the pressure under harsh conditions, such as strong electromagnetic interference and high pressure. It is built on the basis of the fiber-optic Fabry–Perot (F–P) interference and the temperature sensitive mechanism of fluorescent materials. Both halogen lamps and light-emitting diodes (LED) are employed as the excitation light source. The reflected light from the sensor contains the low coherent information of interference cavity and the fluorescent lifetime. This information is independent due to the separate optical path and the different demodulation device. It delivers the messages of pressure and temperature, respectively. It is demonstrated that the sensor achieved pressure measurement at the range of 120–400 KPa at room temperature with a sensitivity of 1.5 nm/KPa. Moreover, the linearity of pressure against the cavity length variation was over 99.9%. In the meantime, a temperature measurement in the range of 25–80 °C, with a sensitivity of 0.0048 ms/°C, was obtained. These experimental results evince that this kind of sensor has a simple configuration, low-cost, and easy fabrication. As such, it can be particularly applied to many fields.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Miniature Fiber Pressure Sensor Based on an In-Fiber Confocal Cavity

Tingting Wang,Yixian Ge,Haibin Ni,Jianhua Chang,Jiahong Zhang,Wei Ke

DOI: https://doi.org/10.1016/j.ijleo.2018.06.151

IF: 3.1

2018-01-01

Optik

Abstract:A new type of miniature pressure sensor based on a hybrid Fabry-Perot (F-P) interferometer is proposed. The in-line air cavity of the sensor is a micro-confocal air cavity, which is formed by splicing together a single mode fiber (SMF) and a solid-core photonic crystal fiber (PCF) with the specific splicing parameters. The sensor is fabricated by simple steps involving only fusion splicing, cleaving and polishing. Optical interference principle of the sensor is analyzed and the parameters in sensor design are discussed. Due to low propagation loss, experiments show that the reflection spectrum of the sensor has a fringe contrast of more than 30 dB. By tracing the trough wavelength in the interference spectrum, the pressure can be demodulated. Within the pressure measurement range of 0-1 MPa, the sensitivity is -193 pm/MPa. The experimental results indicate that the deflection is consistent with the theoretical analysis and the sensor has a good linearity. Easy fabrication, low-cost and high-contrast make it appropriate for practical application.
Optical Fiber Pressure Sensor Based on SMF-Capillary Structure

Y. B. Yang,D. N. Wang,Ben Xu

DOI: https://doi.org/10.1109/acp.2018.8596264

2018-01-01

Abstract:we propose and demonstrate an optical fiber pressure sensor based on the SMF-Capillary structure with a pressure sensitivity of -4.027nm/MPa. It has the characteristics of convenient manufacturing and strong robustness.

A Fiber-Shaped Light-Emitting Pressure Sensor for Visualized Dynamic Monitoring

High-resolution Electroluminescent Imaging of Pressure Distribution Using a Piezoelectric Nanowire LED Array

Single Optical Microfiber Enabled Tactile Sensor for Simultaneous Temperature and Pressure Measurement

Flexible Liquid-Filled Fiber Adapter Enabled Wearable Optical Sensors

Mono-Fiber Optic Pressure Sensor

High-Sensitivity Microfiber Strain and Force Sensors

A Wearable Pressure Sensor Based on the Array of Polymeric Piezoelectric Fiber with Metal Core.

Pressure Visualization and Quantification Photonic Skin Based on Flexible Optical Fiber Combiner

A Novel High-Sensitivity Fiber Grating Sensor for Simultaneous Measurement of Temperature and Pressure

High-Resolution Dynamic Pressure Sensor Array Based on Piezo-phototronic Effect Tuned Photoluminescence Imaging

Simultaneous Measurement of Pressure and Temperature Using a Single Fiber Bragg Grating

An Optical Fiber Pressure Sensor Based on F-P Interferometry and Intensity Demodulation

Self-powered, ultrasensitive, and high-resolution visualized flexible pressure sensor based on color-tunable triboelectrification-induced electroluminescence

A Fiber-Optic Pressure Sensor with Reflecting Optical Structure for the Simultaneous Measurement of Temperature

Optoelectronic Pressure Sensor Based on the Bending Loss of Plastic Optical Fibers Embedded in Stretchable Polydimethylsiloxane

A Transflective Nano-Wire Grid Polarizer Based Fiber-Optic Sensor

Recent Progress in MEMS Fiber-Optic Fabry–Perot Pressure Sensors

Research on the Fabrication and Parameters of a Flexible Fiber Optic Pressure Sensor with High Sensitivity

Hybrid Fiber Optic Sensor, Based on the Fabry–Perot Interference, Assisted with Fluorescent Material for the Simultaneous Measurement of Temperature and Pressure

Miniature Fiber Pressure Sensor Based on an In-Fiber Confocal Cavity

Optical Fiber Pressure Sensor Based on SMF-Capillary Structure