Abstract:Mechanical behaviors of a Ni-based single crystal superalloy have been investigated by tensile testing at various temperatures. Deformation substructures and mechanisms have been systemically revealed from micrometer to atomic scales by using advanced scanning electron and scanning transmission electron microscopes. Results show that deformation mode of the alloy strongly depends on the temperature due to competitive responses of the gamma and gamma' phases under mechanical loading and their original stress statuses. At temperatures from ambient to 750 degrees C, plasticity is governed by dislocation shearing in both phases, where slip modes of gamma are < 110 >{111} and those of gamma' are < 112 >{111}, < 110 >{111} and < 110 > {001}. At moderate temperatures (850 degrees C <= T <= 900 degrees C), plasticity mainly involves microscopically uniform deformation of both phases. The matrix deforms first so that channels parallel to tensile direction are narrowed due to the Poisson's effect, after that deformation of gamma' follows. The active slip modes are < 110 > {111} for gamma, < 112 >{111}, < 110 >{111}, < 110 >{001}, and < 001 >{001} for gamma'. At temperature higher than 1000 degrees C, plastic strain is also derived from deformation of both phases, but deformation of the matrix plays critical roles, due to relatively weak strength of this phase. The operative slip modes are < 110 > {111} for gamma, but mainly < 110 >{001} and < 001 >{001} for gamma'. Our results clearly provide a comprehensive and multiscale (from micrometer to atomic) understanding on the deformation mechanism of Ni-based superalloys, which can be critically beneficial and offer mechanistic guidelines to design new/next generation superalloys. (c) 2021 Elsevier Ltd. All rights reserved.

Study on High Temperature Deformation Behavior of WC-10 Wt %ni3al Cemented Carbide

Influence of Zrc Content on the Elevated Temperature Tensile Properties of Zrcp/W Composites

Effect of High Temperature Annealing on the Microstructure and Thermal Shock Resistance of Tungsten Coatings Grown by Chemical Vapor Deposition

Microstructures and Properties of WC-10 wt.%CoCrFeNiAlx Composite Cemented Carbides

High temperature fracture mechanism of ultrafine WC-Co cemented carbides containing (Ti,W)C

Extraordinary High-Temperature Mechanical Properties in Binder-Free Nanopolycrystalline WC Ceramic

Microstructure and properties of coarse WC-10CoCrFeMnNi cemented carbide by mechanical alloying and hot pressing sintering

Temperature Effects on Deformation Substructures and Mechanisms of a Ni-based Single Crystal Superalloy

Ultrafine Binderless WC-based Cemented Carbides with Varied Amounts of AlN Nano-Powder Fabricated by Spark Plasma Sintering

Microstructure, mechanical and tribological properties of multilayer grapheme reinforced WC-10Ni 3 Al prepared by microwave sintering

Low temperature pressureless immediate sintering of novel nanostructured WC/Co/NiCrSiB-alloy cemented carbide

Insights into High‐Temperature Uniaxial Compression Deformation Behavior of Ti3AlC2

Study on Effect of High-Entropy Alloy Binder on Microstructure and Properties of WC Cemented Carbide Doped with Rare Earth Oxide

High-Entropy-Alloy CoFeNiCr Bonded WC-Based Cemented Carbide Prepared by Spark Plasma Sintering

Study on the high temperature tensile properties and strengthening mechanism of nitrogen containing nickel‐based deposited metals

Deformation mechanisms of Al0.1CoCrFeNi at elevated temperatures

Tribological Performance and Wear Mechanism of Laser Cladded NiCrAl-WC Coatings at High-Temperature

Peculiarities of Preparation and Properties of Cemented Carbide WC + 20 Mass% Ni with Ultra-Coarse-Grained Microstructure

Enhanced high temperature mechanical properties of WC-Co cemented carbides by VC addition

Hot deformation behavior and microstructure evolution of a high Nb containing PM TiAl composite reinforced with Ti2AlC particles

Effect of Microstructure on High Temperature Mechanical Properties in Forming Ni-20cr-10mo-10co Superalloy