Abstract:The thickness of steel plates used in the member has gradually increased to meet the load-bearing capacity requirements of long-span steel bridges. As the primary connection method of thick steel plate, welding will result in considerable welding residual stress with complex distribution. Large welding residual stress will significantly impact the performance of steel bridges. In this paper, the distribution of residual stress in welded thick steel plate is systematically studied, a specimen with a thickness of 80 mm was designed and fabricated, and the welding residual stress was measured by X-ray diffraction. The finite element model was established and verified by test results. Subsequently, the finite element calculation of the welding residual stress of steel plates with thicknesses of 20, 40, 60, 80, and 100 mm was carried out, and the distribution of surface residual stress and the influence of plate thickness on residual surface stress were studied; then the spatial evolution mechanism of welding residual stress was studied, and the distribution of residual stress inside steel plate and the influence of plate thickness on the distribution of residual stress were revealed. The results show that the surface and internal residual stresses of 20–100 mm thick plates have good symmetry on the paths perpendicular to the weld seam, and asymmetry only occurs in the weld seam and heat-affected zone where the stress fluctuates. On the paths perpendicular to the weld seam, the stress in the X direction transitions from the "M" shape distribution on the surface to the "Π" shape distribution inside for 20–40 mm thick plates, and the residual stress near the weld seam gradually changes from compressive to tensile; The distribution of stress in the X direction in the 80–100 mm thick plate has experienced the transition from "M" shape to "Π" shape to "M" shape, and the stress near the weld seam has experienced the transition from compressive to tensile to compressive. The stress change in the X direction of the 60 mm thick plate is between the above two cases. On the path of internal stress along the thickness, the maximum stress in the X direction is 310–400 MPa for 20–40 mm thick plates, which appears at about 1/2 plate thickness. The maximum stress in the X direction for 60–100 mm thick plates is 400–480 MPa, which appears at 0.2–0.3 times the thickness of the plate from the upper surface. The results could serve as a reference for welding residual stress analysis and guide optimization design of steel bridges made of thick steel plate.

Influence of Deposition Sequence and Thickness of Tube on Welding Residual Stress and Deformation in Dissimilar Steel Tube-block Welded Joint

Assessing the Residual Stresses in Dissimilar Welded Joint: Depth-Sensing Indentation Testing and Numerical Simulation

DIC/DSI Based Studies on the Local Mechanical Behaviors of HR3C/T92 Dissimilar Welded Joint During Plastic Deformation

Numerical Prediction and Control of Deformation and Residual Stress in Double-Sided Arc Welding of Large Pressure Hull

Prediction of Residual Stress Distributions in Welded Sections of P92 Pipes with Small Diameter and Thick Wall Based on 3D Finite Element Simulation

Influence of welding sequences and boundary conditions on residual stress and residual deformation in DH36 steel T-joint fillet welds

Effect of different welding parameters on residual stress and deformation of 20/0Cr18Ni9 dissimilar metal arc-welding joint

Effect of welding layers and interlayer temperature on welding residual stress and deformation of Q345/316L dissimilar steel

Thermal, metallurgical and mechanical analysis of circumferentially multi-pass welded P92 steel pipes

Numerical Simulation of Tube-Plate Welding Structure with T-Shaped Sections

Influence of Material Model on Prediction Accuracy of Welding Residual Stress in an Austenitic Stainless Steel Multi-pass Butt-Welded Joint

FE analysis of residual stress and welding deformation of a low-alloy UHS quenched steel fillet joint

Numerical computation methods of welding deformation and their application in bogie frame for high-speed trains

Experimental research and numerical analysis of welding residual stress of butt welded joint of thick steel plate

Effect of Welding Sequence and the Transverse Geometry of the Weld Overlay on the Distribution of Residual Stress in the Weld Overlay Repair of T23 Tubes

The Development of a Continuous Constitutive Model for Thin-Shell Components with A Sharp Change in the Property at Welded Joints

Numerical and experimental study on thermal-metallurgical-mechanical behavior of high-strength steel welded joint

Effect of Tube Arrangement on the Welding of the Tube-to-Tubesheet Joint of Shell-and-Tube Heat Exchangers Using the Finite Element Method

3D finite element analysis and optimization of welding residual stress in the girth joints of X80 steel pipeline

Predicting Welding Residual Stress of a Multi-pass P92 Steel Butt-Welded Joint with Consideration of Phase Transformation and Tempering Effect

Three-dimensional finite element analysis of residual stresses in dissimilar steel pipe welds