Abstract:Effective thermal conduction between solid interfaces has emerged as a major bottleneck in heat dissipating heat from new-generation high-performance electronics. Gallium-based liquid metals (LMs), known for their high thermal conductivity, are gaining significant traction as thermal interface materials (TIMs) for enhanced thermal management. In this work, to address the key issues facing the application of gallium-based LMs as TIMs, including the lack of composition ratio data, poor coating performance and the need for improved thermal conductivity, two types of gallium-based LM-TIMs (Ga-In binary LM-TIMs and Ga-In-Sn ternary LM-TIMs) with different composition ratios were experimentally prepared, investigated and optimized. The thermal conductivities of the LM-TIMs at different temperatures (80 - 120 ℃) were tested, and the application reliability of the LM-TIMs was optimized by continuously destructing the oxide layer and filling micro copper particles. The influence of optimization parameters such as the duration of the destruction of oxide layer, the filling ratios of the particles and the particle size on the operation performance of the LM-TIMs was studied and analyzed. The results showed that the LM-TIMs exhibited excellent thermal conductivities of 29.6 - 38.5 W/(m·K), and the thermal conductivity increased with indium mass fraction and decreased with tin mass fraction. Significant improvements in coating performance were observed with the increase of the duration of destructing oxide layer, but it led to a reduction in thermal conductivity. Balancing coating performance and thermal conductivity, it was found that 30 min was the ideal duration. The filling of micro particles made up for the reduced thermal conductivity, and higher filling ratios and smaller particle sizes achieved better enhancement. In the experiment, a filling ratio of 5 % was appropriate because solidification occurred in LM-TIMs at higher filling ratios which weakened the thermal conductivity. This work provided valuable reference for the application and optimization of high thermal conductive gallium-based LM-TIMs.

ENHANCEMENT OF GALLIUM PHASE-CHANGE HEAT TRANSFER BY COPPER FOAM AND ULTRASONIC VIBRATION

Experimental Investigation on Optimization of the Performance of Gallium-Based Liquid Metal with High Thermal Conductivity As Thermal Interface Material for Efficient Electronic Cooling

Experimental Study on the Heat Transfer Performance of a Gallium Heat Sink

Melting of A Phase Change Material Filled in A Metal Foam: A Visualized Study at the Pore-Scale Using Infrared Imaging

Enhancing heat transfer and melting rates in Large-scale gallium cavities: The impact of buoyancy forces and magnetohydrodynamics

An Enhanced Heat Transfer Method Based on the Electrocapillary Effect of Gallium-Based Liquid Metal

Heat Transfer Characteristics of the Melting Process of the Metal Foam/Paraffin Compound Material

Experimental visualization on thermal energy storage enhancement through metal foam filled annuli

Compression effect of metal foam on melting phase change in a shell-and-tube unit

Improved phase change performance of ultrasonic-assisted melting: A visualized experimental study

Heat transfer enhancement for thermal energy storage using metal foams embedded within phase change materials (PCMs)

Investigation on the Melting Performance of a Phase Change Material Based on a Shell-and-Tube Thermal Energy Storage Unit with a Rectangular Fin Configuration

Experiment on Thermal Conductivity Enhancement for PCM Embedded in Metal Foam

Fast Solidification of Pure Gallium at Room Temperature and Its Micromechanical Properties

How can copper foam better promote the melting process of phase change materials

Sustainable Thermal Regulation of Electronics via Mitigated Supercooling of Porous Gallium-Based Phase Change Materials

COMPARISON ON ENHANCED PHASE CHANGE HEAT TRANSFER OF LOW MELTING POINT METAL MELTING USING DIFFERENT HEATING METHODS

Experimental investigation of the effect of copper foam pore structure on the thermal performance of phase change material in different centrifugal force fields

Experimental and simulation study on the heat transfer mechanism and heat storage performance of copper metal foam composite paraffin wax during melting process

Modification and Pool Boiling Performance Elevation of Copper Foam Wicks for High Power Applications

Effect of enhancement in metal foam pore density on heat transfer of phase-change materials