Abstract:Thick superconducting multilayer architectures consisting of alternate superconducting and superconducting layers DyBCO/YBCO and alternate superconducting and insulating layers YBCO/CuO(Y2O3) are developed on buffered Hastelloy tapes using a metal organic deposition process. It is revealed that multilayer intermittent structures for superconducting layers are effective to avoid the presence of microcracks that occur with increasing thickness, which are frequently observed in monolayer films ofREBa(2)Cu(3)O(7-delta) (REBCO, RE= Y, Gd, or other rare earth elements). This paper shows that the thicknesses of DyBCO/YBCO multilayer films can reach 2.8 mu m with a homogeneous, dense and crack-free surface morphology. The out-plane FWHM of the YBCO (005) peaks and the critical current value reach 1.1 degrees and 365 A/cm (77 K, self-field) for such a thick film consisting of Dy-BCO/YBCO multilayers. It is also revealed that the introduction of a CuO layer is effective to avoid the presence of a-axis grains and voids of the YBCO films, which are frequently observed in multilayer films. Note that the introduction of CuO shows little negative influence on the texture of multilayer structure, especially for the bottom CuO. However, the in-plane texture deteriorates seriously for Y2O3/YBCO/YBCO multilayer film. The critical current density of YBCO films with middle CuO and bottom CuO are 2.0 MA/cm(2) and 2.5 MA/cm(2) (77 K, self-field), respectively. The microstructure optimization including the texture, uniformity, crack, defect, and porosity in the multilayered films is probably the reason for the enhancement of superconducting performance.

Improvement of Bi-Layered YBCO Superconducting Films by Using Ag and Au Interlayers

Fabrication and Analysis of Tri-layer YBa 2 Cu 3 O 7− δ Thick Films by Low-Fluorine MOD Method

Fabrication And Analysis Of Tri-Layer Yba2cu3 O (7-Delta) Thick Films By Low-Fluorine Mod Method

Fabrication and Analysis of Tri-layer YBa2Cu3O7−δ Thick Films by Low-Fluorine MOD Method

Drastic improvement of surface structure and current-carrying ability in YBa2Cu3O7 films by introducing multilayered structure

Preparation and properties of YBCO/Bi-2212/YBCO superconducting trilayer films by acetate based sol–gel method

Ag Doping Effects on Y0.5Gd0.5Ba2Cu3O7−δmultilayers Derived by Low-Fluorine Metalorganic Solution Deposition

Enhanced superconductivity of YBCO interfaces: origin of high critical temperature in layered superconductors

Investigations on the Lead Acetate Addition in Precursor Solutions for YBCO Superconducting Film Deposition

Enhancing superconductivity of ultrathin YBa<sub>2</sub>Cu<sub>3</sub>O<sub>7-δ</sub> films by capping non-superconducting oxides*

Artificial Multilayers of REBaCuO/YBaCuO and YBCO/CuO(Y2O3) for High-Performance Long Tapes of Coated Conductors Derived by Metal Organic Solution Deposition

Chemical Solution Derived YBa2Cu3.3O7-δ/Y2O3(CuO) Multilayers on Oxide Buffered Metallic Tapes

Enhancing Superconductivity of Ultrathin YBa2Cu3O7-δ Films by Capping Non-Superconducting Oxides*

Thick $\Hbox{yba}_{2}\hbox{cu}_{3}\hbox{o}_{7-\Delta}$ Superconducting Films by Low-Fluorine Metallorganic Solution Deposition

Property Improvement of 600-Nm-thick YBCO Superconducting Films Fabricated Using a Pb-Modified MOD Method

Preparation of Yba2cu3o7-X Superconducting Thin-Films over Large Area Substrates

In-Plane and Out-of-Plane Anisotropy in the Optical and Dielectric Properties of Yba2cu3o7-X Superconducting Film

Influence of Partial Melting Temperature on Structure and Superconducting Properties of YBCO Film by Non-fluorine MOD

AG DOPING EFFECTS OF YBCO BY LOW FLUORINE MOD METHOD

Improved Superconducting Performance of YBCO-Coated Conductors by Low Energy Density Argon Ion Etching

Effect of Fired Temperature on Microstructure and Superconductivity of MOD-YBCO Thin Films