Abstract:Recent years have witnessed an increasing use of high strength aluminium alloys in structural applications, however, the mechanical properties of this type of materials are rather susceptible to elevated temperatures. This paper presents an experimental study on the mechanical properties of 7A04-T6 high strength aluminium alloy at elevated temperatures and after cooling down. Tensile coupon tests were first carried out on the specimens at high-temperature steady state conditions and post-fire conditions for temperatures ranging from 20 to 400 °C. The effect of cooling methods (cooled by air/water) was taken into account in the post-fire tests. Key mechanical properties, including Young’s modulus, yield strength, ultimate strength and ultimate strain, as well as the stress–strain responses obtained from both tests were fully reported and the microstructures of the post-fire material were examined. It is shown that the Young’s modulus and strengths decrease dramatically when temperatures are higher than 200 °C and the strengths decrease to less than 5% of the room temperature values at 400 °C, but a large proportion (up to 90%) of them regains after cooling down. In addition, the post-fire mechanical properties of the material exposed to 400 °C was found to be higher than those exposed to 300 °C; this was further explained through the microstructure examination. The test data were then utilised to assess the accuracy of existing codified design methods and the comparisons revealed that all of them provide inaccurate and scattered predictions. Finally, design formulae for the elevated-temperature retention factors as well as the post-fire residual factors and a two-stage Ramberg–Osgood material model were proposed. The design proposal was found to provide accurate predictions for the full-range stress–strain responses of the high strength aluminium alloy at both high-temperature steady state and post-fire conditions.

Identification of 7B04 Aluminum Alloy Anisotropy Yield Criteria with Conventional Test and Pottier Test at Elevated Temperature

Plastic anisotropic behavior of a 2B06-W aluminum alloy sheet

Investigation on Yield Behavior of 7075-T6 Aluminum Alloy at Elevated Temperatures

Characterization on the thermal anisotropic behaviors of high strength AA7075 alloy with the Yld2004-18p yield function

Effect of Different Yield Criteria and Material Parameter Identification Methods on the Description Accuracy of the Anisotropic Behavior of 5182-O Aluminum Alloy

Identification of the Anisotropic Yield and Hardening Constitutive Parameters for Aluminum Alloys Using the Virtual Fields Method

Investigation of formability of aluminum alloy sheet at elevated temperature

Study of Hot Deformation Behavior of 6082 Aluminum Alloy

Investigation on Warm/hot Hydro-Forming of High Strength Aluminum Alloy Sheet

Mechanical Properties of Super-High Strength Al Alloy 7a04 at Transient Heating

Material modeling of 6016-O and 6016-T4 aluminum alloy sheets and application to hole expansion forming simulation

Anisotropic Behavior and Temperature-Dependent Mechanical Properties of Aa1060 Aluminum Alloy: A Comprehensive Microstructural Study

Anisotropic mechanical behavior prediction of aluminum alloy sheet based on an anisotropic GTN model: Modeling, simulation and experimental investigation

Anisotropic Tensile Behavior and Related Yield Point Phenomena in Annealed Ultrafine-Grained Pure Aluminum

Mechanical properties of 7A04-T6 high strength structural aluminium alloy at elevated temperatures and after cooling down

Dynamic Mechanical Behavior and Numerical Simulation of 6013-T4 Aluminum Alloy at Different Temperatures and Strain Rates

Finite Element Modeling for Deep-Drawing of Aluminum Alloy Sheet 6014-T4 Using Anisotropic Yield and Non-Afr Models

Tensile Behavior and Microstructure Evolution of an Extruded 6082 Aluminum Alloy Sheet at High Temperatures

Mechanical Behavior of Commonly Used Aeronautical Aluminum Alloys under Dynamic Tension

The Anisotropic Property of 7075-T6 Aluminum Alloy under Warm Condition

High-Temperature Mechanical Behavior of an As-Extruded Al-5Zn-2Mg-0.3Cu (in wt.%) Alloy