Abstract:This study explores the intricate interplay between strain-induced precipitation (SIP) and the underlying mechanisms that govern hot deformation in AA6082 aluminum alloy. Uniaxial tensile tests were conducted at elevated temperatures, ranging from 200°C to 400°C, and varied strain rates from 0.01 s −1 to 10 s −1 . Employing advanced methodologies such as scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), energy dispersive X-ray spectrometry (EDS), and transmission electron microscopy (TEM), the research investigates the relationship between deformation, precipitation, and structural evolution. At lower strain rates, longer deformation times promote dynamic recrystallization, thereby promoting the growth of substructures with enhanced ductility. On the contrary, at higher strain rates (10 s −1 ), shorter deformation times inhibit such processes, resulting in a clear predominance of dislocation motion along specific slip systems and consequently influencing the mechanical response of the alloy. The results also reveal temperature-dependent deformation mechanisms, such as intragrain slip, continuous dynamic recrystallization (CDRX), and SIP phenomena, which influence the alloy's mechanical response. At 200°C, prominent work hardening dominates, while 400°C exhibits dynamic softening mechanisms. EBSD analyzes elucidate temperature-specific deformation mechanisms, including intragrain slip at 200°C and transitional phenomena at 300°C. Microstructural analysis at 200°C reveals the absence of needle- or rod-shaped precipitates. On the contrary, at 300°C, the presence of β/β' precipitates significantly influences the nucleation of β'' precipitates at the grain boundaries. At 400°C, substantial rod-shaped β' phase precipitates appear, demonstrating a complex interplay between diffusion mechanisms and strain-induced effects. In addition, the study also investigated the fracture behavior of aluminum alloy at different tensile temperatures, revealing the transition from transgranular fracture at 200°C to intergranular fracture at 300°C, as well as the shear effect of β/β' phase precipitates at this temperature. The findings provide a comprehensive understanding of the alloy behavior under diverse conditions, essential to optimize its processing parameters and mechanical properties.

Anisotropic Behavior and Temperature-Dependent Mechanical Properties of Aa1060 Aluminum Alloy: A Comprehensive Microstructural Study

Anisotropic Tensile Behavior and Related Yield Point Phenomena in Annealed Ultrafine-Grained Pure Aluminum

High-Temperature Tensile Mechanical Properties and Microstructure of Rolled 6082-T6 Aluminum Alloy Sheets

Mechanical Properties and Surface Characteristics of an AA6060 Alloy Strained in Tension at Cryogenic and Room Temperature

Advancement of microstructural evolution and deformation mechanisms in AA6082 aluminum alloy under elevated-temperature tensile loading

Mechanical Properties and Microstructural Evolution of 6082 Aluminum Alloy with Different Heat Treatment Methods

Anisotropic Mechanical Behavior and Microstructural Characteristics of AA2099-T83 Alloy Sheet: Experiment and Simulation

Effect of Initial Orientation on the Anisotropy in Microstructure and Mechanical Properties of 2195 Al-Li Alloy Sheet during Hot Tensile Deformation

Tensile Behavior and Microstructure Evolution of an Extruded 6082 Aluminum Alloy Sheet at High Temperatures

Cryogenic Temperature And Strain Rate Dependence Of Mechanical Properties For Extruded Aa6060 Alloys

Effects of Cold Rolling and Heat Treatment on Microstructure and Mechanical Properties of AA 5052 Aluminum Alloy

Good Combination of Strength and Mechanical Isotropy in AA6082 Alloy Processed by High Temperature Intermediate Annealing

Experimental Investigation of Mechanical Properties of Aluminum Alloy at High and Low Temperatures

Anisotropic behavior and mechanical properties of Ti-6Al-4V alloy in high temperature deformation

Microstructure and Mechanical Property of Aluminum Alloy Plate AA 7055

Microstructures and Properties of Al-Mg-Sc Aluminum Alloy Sheet at Different Orientations

Elevated-temperature and Post-Fire Performance of 6013-T6 High-Strength Aluminum Alloy: Experimental Study, Predictive Equations and Constitutive Models

Investigation on Yield Behavior of 7075-T6 Aluminum Alloy at Elevated Temperatures

Controlled Annealing of Sandwich-Structured Aluminum AA1050 for Optimized Combinations of Strength and Ductility

Experimental Study on Mechanical Property of Chinese Structural Aluminum Alloy at Low Temperatures

Effect of three-dimensional deformation at different temperatures on microstructure, strength, fracture toughness and corrosion resistance of 7A85 aluminum alloy