Abstract:The present study investigated influences of the Al3Sc particle content on the evolution of bimodal grain structure and mechanical properties at both room and elevated temperatures of Al–7Mg–Sc alloys processed by hard-plate rolling (HPR). Bimodal grain structures were obtained in HPRed Al–7Mg–Sc alloys where ultrafine/fine grains decreased in size and increased in amount with increasing volume fraction of Al3Sc precipitates. The formation and evolution of bimodal grain structure are associated with (i) the different stability of various-orientated grains, and (ii) the volume fraction of Al3Sc precipitates. Ultrafine/fine (sub) grains form preferentially along grain boundaries (GBs) of <001>//normal direction (ND)- and <111>//ND-oriented coarse grains during HPR. In contrast, the <101>//ND-oriented coarse grains show relatively high stability nearly without subdivision. Furthermore, increased volume fraction of Al3Sc precipitates in Al–7Mg–0.4Sc promotes dislocation accumulation, favoring recrystallization nucleation, and meanwhile restricts grain growth, which results in more and refined ultrafine/fine grains. Thereby, the refined grain structure and increased volume fraction of Al3Sc precipitates in the Al–7Mg–0.4Sc alloy contribute to improved room-temperature yield strength (YS) and elongation, i.e. ~482 MPa and ~8%, which is much higher than that of ~420 MPa and ~4% in the binary Al–7Mg alloy. Meanwhile, Al–7Mg–0.4Sc exhibited higher hardness when annealed at 150–300 °C and also higher YS when subjected to a tensile test at ≤ 200 °C due to the more stabilized grain structure pinned by dispersed Al3Sc and additional strengthening effect from Al3Sc precipitates. Nevertheless, when subjected to a tensile test at ≥ 250 °C, the Al–7Mg–0.4Sc alloy exhibited much lower YS than binary Al–7Mg. The transition could be explained by more favored grain boundary sliding (GBS) and great dislocation loss, due to the easier occurrence of dynamic recrystallization (DRX) in Al–7Mg–0.4Sc during tensile test at elevated temperatures.

Microstructures and Properties of Al-Mg-Sc Aluminum Alloy Sheet at Different Orientations

The Dependence of Final Microstructure, Texture Evolution and Mechanical Properties of Al–Mg–Si–Cu Alloy Sheets on the Intermediate Annealing

New insight of texture and microstructure evolution, and the connections between with tensile performance in as-annealed Al-Cu-Mg-Zr sheet

Effect of Microstructures on the Anisotropy of the Roll Casting Strip of Cold Rolled 3003 Aluminum Alloy

Effect of Alloying Elements and Processing Parameters on Microstructure and Properties of 1XXX Aluminium Alloys

Microstructures and textures in cold-rolled aluminium strip

Microstructure and properties of Al-4.8Cu-0.45Mn-0.19Cd-0.18Ti-0.17Zr-0.14V aluminum alloy extrusion bar

Investigation of particles on the microstructure, texture and formability of Al–Mg-Si-Zn alloy for automotive body sheet

Influence of Asymmetric Rolling on the Microstructure, Texture Evolution and Mechanical Properties of Al–Mg–Si Alloy

A Comparison Study Of Microstructure, Texture And Mechanical Properties Between Two 6xxx Aluminum Alloys

Deformation mechanism, orientation evolution and mechanical properties of annealed cross-rolled Mg-Zn-Zr-Y-Gd sheet during tension

Microstructure and Texture Evolution of Cold Rolled 1070 Al Alloy During the Subsequent Annealing Treatment

Enhanced formability of Al–Mg–Si–Zn alloy sheet via dislocation structure and texture during cold rolling

Effect of Initial Orientation on the Anisotropy in Microstructure and Mechanical Properties of 2195 Al-Li Alloy Sheet during Hot Tensile Deformation

Effect of recrystallization annealing, solid solution and pre-aging intermediate treatment on microstructure and mechanical properties of Al-Mg-Si rolled sheet

Microstructure evolution and mechanical properties of Al-Cu-Li alloys with different rolling schedules and subsequent artificial ageing heat treatment

Anisotropic Mechanical Behavior and Microstructural Characteristics of AA2099-T83 Alloy Sheet: Experiment and Simulation

Effect of Rolling Temperature on Microstructure and Properties of Al-Mg-Li Alloy

Effect of annealing process on microstructure and mechanical properties of precipitated phase of A1235 aluminum alloy

Anisotropic Tensile Behavior and Related Yield Point Phenomena in Annealed Ultrafine-Grained Pure Aluminum

Influences of the Al3Sc particle content on the evolution of bimodal grain structure and mechanical properties of Al–Mg–Sc alloys processed by hard-plate rolling