Abstract:Sheet metals usually exhibit a certain degree of plastic anisotropy because of the rolling effect. To characterize the anisotropic behavior in simulations related to large deformation, strain-rate independent phenomenological models are frequently used in quasi-static conditions. Two functions are generally included in such a model, i.e. the yield function and the plastic potential. The former limits the stress state within the yield surface while the latter determines the direction of the plastic strain increment. Traditional plasticity models mostly assume associated flow rule, in which the two functions mentioned above are identical. With the enhanced demand of accuracy, the forms of the associated models become too complex with more and more parameters to achieve an easy calibration procedure. Alternatively, in the past decade the non-associated models were increasingly used for sheet metals. Separate functions for the two aspects of plasticity lead to efficient characterization and convenient calibration. In numerical study of dynamic loading cases, how to characterize strain-rate dependence of plasticity is an important issue. Some visco-plastic models were developed to take the rate effect into account, e.g. Johnson-Cook and Cowper-Symonds models, where the isotropic J2 flow theory was commonly used. However, when the material is severely anisotropic, this approach is very likely to be insufficient, and a model including both anisotropy and rate dependence would be needed. Extending a non-associated anisotropic model to be rate-dependent is a promising approach which has not been published in open literature to the best knowledge of the authors. Objective of the present study is to develop an applicable model for characterizing dynamic mechanical behavior of a typical high-strength steel sheet. Two steps are performed. The material is investigated under quasi-static loading firstly. Tensile test results show an obvious anisotropy which cannot be described by traditional associated models. So the non-associated Hill48 model is chosen and calibrated. Accuracy of the model is verified by a quasi-static punching test. Thereafter the dynamic material properties are obtained by conducting tensile tests at quite a few strain-rate levels covering 0.0004–1200s−1. To characterize the positive strain-rate effect in strength, the non-associated Hill48 model is extended to be visco-plastic after checking two rate-dependence formulations in existing isotropic models. With implementing the extended model into a user subroutine of ABAQUS/explicit, simulations of the dynamic tension tests are run and compared to the real experiments. A good agreement between the simulated and the experimental result is achieved using the VUMAT.

Anisotropic mechanical behavior prediction of aluminum alloy sheet based on an anisotropic GTN model: Modeling, simulation and experimental investigation

Finite Element Modeling for Deep-Drawing of Aluminum Alloy Sheet 6014-T4 Using Anisotropic Yield and Non-Afr Models

Anisotropic Ductile Fracture: Experiments, Modeling, and Numerical Simulations

The GTN damage model based on Hill’48 anisotropic yield criterion and its application in sheet metal forming

Modeling of the Ductile Fracture During the Sheet Forming of Aluminum Alloy Considering Non-Associated Constitutive Characteristic

Modeling Anisotropic Ductile Fracture of AA7075-T6 Sheet for Sheet Metal Forming Considering Anisotropic Stress State

Parameters Determination of GTN Model and Damage Analysis of Aluminum Alloy 6016 Sheet Metal

Effects of Anisotropic Yield Criteria on the Prediction of Sheet Metal Forming of Aluminum Alloy Sheet

Forming Limit Prediction of Anisotropic Aluminum Magnesium Alloy Sheet AA5052-H32 Using Micromechanical Damage Model

Ductile fracture prediction in aluminium alloy 5A06 sheet forming based on GTN damage model

Modeling Anisotropic Ductile Fracture Behavior of Sheet Metals Considering Non-directionality of Equi-Biaxial Tensile Fracture

Anisotropic Gurson-Tvergaard-Needleman model considering the anisotropic void behaviors

Material modeling of 6016-O and 6016-T4 aluminum alloy sheets and application to hole expansion forming simulation

The experimental study on plastic flow and anisotropic properties of the new generation Aluminum Lithium alloy sheet

Extension of Non-Associated Hill48 Model for Characterizing Dynamic Mechanical Behavior of A Typical High-Strength Steel Sheet

Ductile Fracture Initiation of Anisotropic Metal Sheets

A Novel Damage Model To Predict Ductile Fracture Behavior For Anisotropic Sheet Metal

Effect of Different Yield Criteria and Material Parameter Identification Methods on the Description Accuracy of the Anisotropic Behavior of 5182-O Aluminum Alloy

Development of a Modified Gurson–Tvergaard–Needleman Damage Model Characterizing the Strain-Rate-Dependent Behavior of 6061-T5 Aluminum Alloy

Extension of the DF2016 Isotropic Model into an Anisotropic Ductile Fracture Criterion

Limitation analysis of the Hill48 yield model and establishment of its modified model for planar plastic anisotropy