Abstract:To further improve the thermal shock resistance and ablation resistance of SiBCN system ceramics targeted much harsh environment, both ultra-high temperature ceramic phases and carbon fibers are expected to be incorporated simultaneously as the reinforcements. However, tough problems like difficulty in densification as well as degradation of C fibers (Cf) due to interfacial reaction usually cannot be avoided. Thus, in this study, Zr as well as chopped Cf with BN coating were introduced into SiBCN ceramics by mechanical alloying and after hot-pressing sintering to prepare C/SiBCNZr composites. The structure and phase component development have been characterized in detail by XRD, SEM, TEM and XPS etc., and mechanical properties, fracture behavior and toughening mechanisms were also investigated. Zr-B and Zr-O bonds are detected besides Si-C, N-B and N-B-C bonds when pre-alloyed ZrB2 amorphous powder was incorporated into SiBCN system by further mechanical-alloying treatment. After hot-pressing, the ultra-high temperature phases of ZrB2 and ZrN were formed as expected besides the original matrix phases of BN(C) and SiC. Excellent mechanical properties can be obtained for SiBCNZr ceramic. The BN coating on carbon fibers successfully avoids the severe fiber degradation and makes it possible for moderating strong interface bonding, which ensuring the debonding, crack deflection, fiber pulling-out and bridging during the fracture. As a result, the C/SiBCNZr composites retain good mechanical properties and fractures in a pseudoplastic fracture manner, showing better potential applications in harsh environments. Optimization of the BN coating on Cf and Zr incorporation by pre-mechanical alloying can be a good route to achieve Cf/SiBCNZr composites with a better balance between thermal shock resistance, ablation resistance and mechanical properties.

Improved toughness of ZrB2–SiC composites with nanopowders obtained by mechanical alloying

Enhanced thermal shock resistance of BN-based composites sintered by hot-pressing with the introduction of nano oxides

Effects of ZrB2 powders on microstructure and mechanical properties of ZrB2-SiCw ceramics

Effect of ball milled Zr/Al/ZrB2 composite powders on microstructure and toughening of ZrB2–SiC/Zr–Al–C composite ceramics sintered by spark plasma sintering

Effects of Zr and chopped C fiber on microstructure and mechanical properties of SiBCN ceramics

SiC and ZrN Nano-Particulate Reinforced AlON Composites: Preparation, Mechanical Properties and Toughening Mechanisms

Synergistic Toughening Effect of SiC Whiskers and Particles in ZrO2–Al2O3–SiC Ceramics

Microstructure and mechanical properties of SiC composite ceramics modified by (TixZr1–x)B2 solid solution

Fabrication and mechanical properties of ZrB2–SiCw ceramic matrix composite

Study on the toughening mechanism of in-situ synthesis (TixZr1−x)B2 in solid-state sintered SiC composite ceramics

Preparation And Mechanical Properties Of Zrb2-Based Laminated Composites

Preparation And Mechanical Properties Of Zirconium Diboride Matrix Composites Reinforced By Silicon Carbon Platelets

Preparation, mechanical properties, and toughening mechanisms of SiCw/SiCp‐reinforced zirconia‐toughened alumina ceramics

Effect of Nano SiC on Microstructure and Mechanical Properties of BN-ZrO2-SiC Multiphase Ceramics

In Situ Preparation and Mechanical Properties of (ZrB2+ZrC)/Zr3[Al(Si)]4C6 Composites

Mechanical Properties of Short Carbon Fiber Reinforced ZrB2–SiC Ceramic Matrix Composites

Simultaneous hardening and toughening of a high entropy (NbTaZrW)C ceramic carbide using SiC particle

Correlation between phase content and mechanical properties of SiCw- ZTA composites sintered by SPS

Microstructure And Mechanical Properties Of Zrb2-Based Composites With Laminated Structure

The Fabrication and Mechanical Properties of SiC/ZrB2 Laminated Ceramic Composite Prepared by Spark Plasma Sintering

The impact of Si3N4 incorporation on the mechanical characteristics of ZrB2-SiC nanocomposite sintered via pressureless method