Abstract:Cold sintering process (CSP) developed recently has attracted much attention due to the ultralow sintering temperatures and high efficiencies with the assist of transient liquid phase (TLP). Based on CSP, we have further established a protocol for low‐temperature sintering processes by combining TLP with other sintering technologies, including hybrid sintering process with microwave and TLP (MW‐TLP), and hybrid sintering process with spark plasma sintering and TLP (SPS‐TLP). Three typical electro‐ceramics (TiO2, CaWO4, and ZnO) are selected, which are highly densified (>97%) with excellent electrical properties at reduced sintering temperatures, applied pressures or holding times, demonstrating the feasibility of MW‐TLP and SPS‐TLP in fabricating electro‐ceramics. Especially, the Q × f value of TiO2 ceramics (38,020 GHz) prepared by MW‐TLP at 1000°C is 46.2% and 23.4% higher than that of microwave and spark plasma sintered samples, respectively, and comparable to traditional thermal sintered (TTS) samples at 1300–1400°C. The dielectric properties of MW‐TLP CaWO4 ceramics sintered at 900°C for 2 h are comparable to TTS samples sintered at 1000–1300°C for 2–5 h. ZnO ceramics can be highly densified (∼98%) by SPS‐TLP with mild sintering conditions (200–300°C and 3.8–50 MPa) compared to SPS (>500°C) and CSP (>100 MPa). The frameworks of fundamental mechanisms are outlined together with the experimental data. It is expected that this work will provide promising sintering methods to fabricate electro‐ceramics and offer inspirations on sintering combinations to develop low‐temperature sintering processes with high efficiencies.

ZrW2O8 with Negative Thermal Expansion Fabricated at Ultralow Temperature: an Energy-Efficient Strategy for Metastable Material Fabrication

ZrW2O8/ZrO2 Composites with Low/Near-Zero Coefficients of Thermal Expansion Fabricated at Ultralow Temperature: an Integration of Hydrothermal Assembly and a Cold Sintering Process

Effects of the Liquid Phase Content on the Microstructure and Properties of the ZrW2O8 Ceramics with Negative Thermal Expansion Fabricated by the Cold Sintering Process

Zr 1− X Yb X WMoO 8− X /2 ( X = 0, 0.04) Ceramics Fabricated by in Situ Synthesis from Trigonal Polymorph: Preparation, Sintering Process, and Negative Thermal Expansion Properties

Near-zero thermal expansion of ZrW2O8/Al–Si composites with three dimensional interpenetrating network structure

Superior overall performance of zero thermal expansion ZrW2O8/Al–Si composite

Negative thermal expansion in a zirconium tungstate/epoxy composite at low temperatures

Preparation and negative thermal expansion in medium-entropy ceramics (Zr1/3Hf1/3Ti1/3)V2O7

Negative thermal expansion in α-Zr2SP2O12 based on phase transition- and framework-type mechanisms

Preparation of Negative Thermal Expansion ZrW2O8 Powders and Its Application in Polyimide/ZrW2O8 Composites

In-situ fabrication and characterization of W-ZrC composites via pressureless reaction sintering

Isotropic negative thermal expansion in ZrW2O8 and HfW2O8 from 1100 to 1275°C

Novel low temperature derived W f /W-ZrC-Cu composites by reactive infiltration with enhanced mechanical and thermal physical properties

Size Effect on the Thermal Expansion of ZrO2/ZrW2O8 Composites Fabricated by the Conventional Sintering Process

Structural, in-situ Raman spectroscopy and XPS studies on ZrW2-Mo O8 ceramics with tunable negative thermal expansion properties

First-Principles Structural, Mechanical, and Thermodynamic Calculations of the Negative Thermal Expansion Compound Zr2(WO4)(PO4)2

Low-Temperature Sintering of Negative–Positive-Zero-Type Temperature-Stable Ceramics with ZnO–B2O3 Flux and SrCO3 Additive

Construction of zirconium tungstate modified polymer bonded energetic composites with highly inhibited thermal expansion via bioinspired interfacial reinforcement

Synthesis And Characterization Of Zirconium Tungstate Ultra-Thin Fibers

Tunable Thermal Expansion and Magnetism in Zr-doped ScF3

Hybrid low‐temperature sintering processes of electro‐ceramics