Abstract:Silica aerogels generally exhibit poor mechanical properties, which seriously restrict their commercial use and makes it necessary to reinforce their structures to obtain materials strong enough to withstand mechanical stresses. The incorporation of polymers into silica aerogels is a promising approach due to the enhancement in mechanical strength afforded and the possibility of imparting the hydrophobicity of the polymers to the resulting aerogels. However, the processes typically employed to prepare polymer-reinforced silica aerogels are complex, arduous and costly, requiring multiple washing and soaking steps for the infiltration of the polymer precursors after gelation and supercritical drying. Additionally, diffusion problems can result in heterogeneity in aerogel monoliths due to the use of various cross-linked polymers and the autoclave-limited dimensions of aerogels. In this study, a facile sol–gel route was developed to fabricate a large (500 cm3) polymer–silica aerogel monolith that was stable under atmospheric conditions and suitable for machining. The synthesis of the polymer–silica aerogels began with a facile one-pot reaction involving resorcinol (R), formaldehyde (F), methyltrimethoxysilane (MTMS), and N-(β-aminoethyl)-γ-aminopropyl-trimethoxysilane (AEAPTES), followed by an ambient-pressure drying process. The resulting aerogels were characterised by nitrogen adsorption–desorption, scanning electron microscopy (SEM), contact angle, and thermal conductivity measurements, and the aerogel mechanical properties were evaluated by a unidirectional compression test. The Young's modulus of compression of the aerogels was observed to increase from 3.95 to 34.88 MPa with an increase in the density of the aerogels from 0.14 to 0.26 g cm−3. Simultaneously, the aerogels were observed to be superhydrophobic, with a contact angle as high as 168°, and exhibited low thermal conductivity (0.038 W m−1 K−1) and good absorption for organic liquids, which are critical characteristics for the practical application of aerogels, especially in energy-saving and oil-/chemical-cleanup practices.

Organic Solvent-Saving Preparation of Water Glass Based Aerogel Granules under Ambient Pressure Drying

Preparation of Hydrophobic Silica Aerogels from Industrial Water Glass

Preparation and Characterization of Hydrophobic Silica Aerogel by Ambient Pressure Drying Method

Preparation of Methyltrimethoxysilane Derived Silica Aerogel Films via Ambient Pressure Drying

Preparation and Heat Treatment of Titania Aerogels by Ambient Pressure Drying

Synthesis of high specific surface area silica aerogel from rice husk ash via ambient pressure drying

Synthesis and characterization of silica aerogels by a novel fast ambient pressure drying process

Hydrophobic waterglass based aerogels without solvent exchange or supercritical drying

A Facile Strategy for Freeze-Drying Preparation of Silica Aerogel from Sodium Silicate

Synthesis of Hydrophobic Silica Aerogels via Ambient Pressure Drying

Preparation of silica aerogel from rice hull ash by drying at atmospheric pressure

Facile Synthesis of Flexible and Hydrophobic Polymethylsilsesquioxane Based Silica Aerogel Via the Co-Precursor Method and Ambient Pressure Drying Technique

Silica aerogels formed from soluble silicates and methyl trimethoxysilane (MTMS) using CO2 gas as a gelation agent

A novel low-cost method of silica aerogel fabrication using fly ash and trona ore with ambient pressure drying technique

In-situ acid catalysis strategy to achieve rapid ambient pressure drying preparation of aerogels

Ambient-pressure drying synthesis of large resorcinol–formaldehyde-reinforced silica aerogels with enhanced mechanical strength and superhydrophobicity

Preparation of Silica Aerogels Via Ambient Pressure Drying

Performance regulation of silica aerogel powder synthesized by a two-step Sol-gel process with a fast ambient pressure drying route

Rapid synthesis of sodium silicate based hydrophobic silica aerogel granules with large surface area

Convenient and rapid preparation of aerogels dried at ambient pressure

Preparation of SiO2 aerogel by water glass: effect of different sodium removal methods on aerogel properties