Abstract:Blowing agents are key compounds for the preparation of polymer foams. However, the use of chemical blowing agents is being curtailed to address the adverse impacts on public health and the environment issues. Moreover, physical blowing agent supercritical carbon dioxide (CO 2 ) requires harsh experimental conditions such as high temperature and pressure, resulting in high energy consumption and safety problems. In this study, CO 2 was captured through amines under atmospheric pressure to form ammonium carbamate salts, which reversibly released under heating as blowing agent. Integrated nucleating-blowing agents were fabricated by heterogeneous nucleating agent (cyclodextrin nanosponges, NS) loaded with ammonium carbamate salts. The effects of types and contents of amines on the thermal and CO 2 capture efficiency were investigated. Results revealed that only amines with strong basicity like 1,2-cyclohexanediamine (TRK) was the CO 2 capture candidate to prepare ammonium carbamate salts. The mass ratio was 1:4 for NS and TRK (NS: TRK-CO 2 (1:4)), and the release temperature of CO 2 was 137 °C. Foamed polyethylene (PE) composites were prepared by molding process with NS: TRK-CO 2 (1:4). Scanning electron microscopy (SEM) images were used to study the morphology of the nanocomposites. The optimum cell morphology was obtained with 5 wt% NS: TRK-CO 2 (1:4), the cell diameter was 116 μm, and the cell density was 7.9 × 10 4 cell/cm 3 . The best fabricated microcellular PE/NS: TRK-CO 2 (1:4) composite presented excellent mechanical, thermal and sound insulating performance. The maximum tensile strength of the PE composite was 25.48 MPa, and the maximum bending strength was 11.27 MPa. The impact strength was 5.77 KJ•m -2 , more than 1.5 times higher than pure PE. The thermal conductivity was as low as 0.076 W/m•k, the sound absorption coefficient was 0.737 at 1500 Hz, and the noise reduction coefficient was 0.459.

Dimensional Stability of LDPE Foams with CO2 + I-C4h10 Mixtures As Blowing Agent: Experimental and Numerical Simulation

Foaming and Dimensional Stability of LDPE Foams with N2, CO2, I-C4h10 and CO2 - N2 Mixtures As Blowing Agents

Anti-shrinking foaming of polyethylene with CO2 as blowing agent

Study on the Foaming Behaviors of PBS and its Modification with PA6IcoT Assisted by scCO2

Effect of Phase Compatibility on the Foaming Behavior of Ldpe/Hdpe and Ldpe/Pp Blends with Subcritical Co2 As the Blowing Agent

Evaluation of LLDPE/LDPE Blend Foamability by in Situ Rheological Measurements and Bubble Growth Simulations

Insight into the Influence of Properties of Poly(Ethylene-co-octene) with Different Chain Structures on Their Cell Morphology and Dimensional Stability Foamed by Supercritical CO2

Foaming polyethylene with CO2-BASED mixtures of blowing agents

Extrusion Foaming of Poly(ethylene Terephthalate) with Carbon Dioxide Based on Rheology Analysis

Evaluating melt foamability of LLDPE/LDPE blends with high LLDPE content by bubble coalescence mechanism

Preparation of high melt strength polypropylene by the reactive extrusion process and its foaming application

Study on Extrusion Foaming of Polypropylene/Polydimethylsiloxane Blends

Super‐Elastic and Dimensionally Stable Polyether Block Amide Foams Fabricated by Microcellular Foaming with CO2&N2 as Co‐Blowing Agents

Numerical simulation of polypropylene foaming process assisted by carbon dioxide: Bubble growth dynamics and stability

Supercritical carbon dioxide foamed thermoplastic polyester elastomer with poly(lactic acid) blending: shrinkage reduction and expansion ratio improvement

Application of Carbon Dioxide Capture Technology in the Process of Polyethylene Foaming Materials

Biodegradable and Ultra-High Expansion Ratio PPC-P Foams Achieved by Microcellular Foaming Using CO2 as Blowing Agent

Halogen‐free Intumescent Flame Retardancy and Mechanical Properties of the Microcellular Polypropylene with Low Expansion Ratio Via Continuous Extrusion Assisted by Subcritical CO 2

Foaming of Linear Isotactic Polypropylene Based on Its Non-Isothermal Crystallization Behaviors under Compressed Co2

Preparation of Biodegradable PBST/PLA Microcellular Foams under Supercritical CO2: Heterogeneous Nucleation and Anti-Shrinkage Effect of PLA

Effect of Interfacial Properties on the Stability of Ultra-Dry CO2-in-water (C/W) Foams Stabilized with Zwitterionic Surfactants and Nonionic/anionic Polymers: Experimental and DPD Simulation